LCU-1651 6C2 7Packages

Statement of Work (SOW) / Performance Work Statement (PWS)

This document details the requirements for replacing the Fuel Oil Fill Shore Connection Piping on the LCU-1651 NBU-7.

• Replace existing fuel oil fill shore connection piping and associated valves.

• Install new piping and valves as specified in the material list.

• Clean existing fuel oil fill shore connection for reuse.

• Fabricate backing rings as required.

• Perform shop low pressure air tests and local air hose tests.

• Conduct an operating pressure test to verify tightness.

• Clean and preserve new and disturbed surfaces.

• Piping must be cleaned to a gas/oil free condition in accordance with 29 CFR 1915 Subpart B.

• Operating pressure test must meet specified criteria with no allowable leakage.

• Report of the Marine Chemist certificate must be submitted.

• Anticipated Award Date: 12/04/2025

• POP Start Date: 5/01/2026

• POP End Date: 9/30/2026

• Production Completion Date: 8/29/2026

• Location: Main Deck, Weather, Port Side, FR 48

• All work must be performed in accordance with referenced standards and diagrams (e.g., 245-2889634 Rev A, 511-2889660 Rev E).

• Government Furnished Material (GFM) will be provided for specific items listed in Section 5.

Statement of Work (SOW) / Performance Work Statement (PWS)

This document outlines the requirements for replacing two existing crew berths in Berthing 2-33-0-L on the LCU 1651 due to degraded conditions.

• Replacement of two (2) existing crew berths with new "3 HIGH-0 LOCKER, Type-III Style-1 Size-2" berths.

• Installation of a left-hand berth at the STBD centerline and a right-hand berth at the PORT centerline.

• Each new berth will be equipped with a berth light fixture and a fan.

• Electrical work to upgrade existing wiring for four fans to accommodate six fans (three per berth).

• Installation of sheathing around the new crew berths.

• Removal of existing joiner doors and reinstallation with new rivets and fasteners.

• Assembly of new crew berths to suit onboard conditions, including adjustment and installation of new subbases and studs.

• Chip and grind surfaces flush and smooth for welding.

• Welding to be accomplished per specified requirements.

• Removal and installation of new components as identified.

• Witnessing of operational tests for newly installed electrical equipment.

• Cleaning and preservation of new and disturbed surfaces.

• Inspection and verification of work completion.

• Anticipated Award Date: 12/04/2025

• POP Start Date: 06/01/2026

• POP End Date: 09/30/2026

• Location: LCU 1651, Berthing 2-33-0-L

• All work to be templated from craft and existing equipment.

• Sharp edges to be ground smooth.

• Affected surfaces to be patched and repaired per NAVSEA Standard Item 009-32.

• Electrical modification to be performed per enclosure (1) of the Liaison Action Record.

• Materials to be used as specified in the document, with allowances for equivalent or activity-furnished materials where noted.

Statement of Work (SOW) / Performance Work Statement (PWS)

This document outlines the "Job Specification" for the "RO Unit Replacement; accomplish Rev-02(FO)~ Fresh Water Tank and Piping; clean" for Hull/Ship LCU-1651 NBU-7.

• Replacement of the RO unit.

• Accomplishment of "Rev-02(FO)" which includes work on the Fresh Water Tank and Piping.

• Cleaning of the fresh water tank and piping.

• Specific locations for work include: Fresh Water Tank (2-40-0-W), RO EQUIP RM (2-40-1-Q), and Equipment Repair Parts Stores (2-40-0-A).

• The work involves a 1,000 Gallon/100 Percent Capacity Fresh Water Tank and approximately 5 feet of 1/2 Inch IPS and 3/4 Inch IPS Fresh Water Piping.

• Cleaning of fresh water tanks and piping using specified guidance (2.3 through 2.5).

• Disinfection of fresh water tanks and piping.

• Bacteriological testing conducted at approved laboratories.

• Cleaning of steel surfaces to bare metal (SSPC-SP-). Specific methods include power tool cleaning (SSPC-SP-3) and hand tool cleaning (SSPC-SP-2).

• Operating pressure test of fresh water piping to verify tightness with no allowable leakage.

• Cleaning and preservation of new and disturbed surfaces to match the surrounding area.

• Visual inspection of tanks, voids, and cofferdams for cleanliness.

• Anticipated Award Date: 4/30/2026

• POP Start Date: 6/01/2026

• POP End Date: 9/30/2016 (Note: This end date appears to be in the past and may be a typo in the source document).

• Production Completion Date: 8/29/1026

• Place of Performance: SASEBO

• References include Standard Items (FY26), specific ELM documents, DWG, LAR, and NAVSEA standards.

• Government Furnished Material (GFM) is listed, including O-RINGS, SPACERS, RETAINER RINGS, INSULATION, CLOTH, ADHESIVE, and RUBBER GASKET SHEET.

• Coordination with ship's force and Damage Control Assistant (DCA) is required for fluid off-loading and transfer.

• Waste liquid removal and disposal must follow specific procedures and contact information.

• Work is related to the replacement of a Desalinator/Reverse Osmosis unit.

Solicitation / RFP / RFQ

This document outlines the "Job Specification" for the "(40) Vehicle Deck Lashing Socket; inspect and replace" on the LCU-1651 NBU-7. The anticipated award date is May 1, 2026, with a period of performance from December 7, 2026, to September 30, 2026.

• Inspect and replace vehicle deck lashing sockets.

• Specific locations for work include the Vehicle Deck, Main Deck, and various tanks, machinery rooms, and living spaces.

• Identification of specific components to be inspected and potentially replaced, including 57 existing vehicle lashing sockets (12-1/2 inch diameter, 3/4 inch thick plate) and 15 new ones.

• Fabrication of a "GO/NO-GO" gauge for inspection.

• Cleaning of affected areas to a gas/oil-free condition.

• Removal and reinstallation of components as needed.

• Welding and non-destructive testing of welded joints.

• Air hose testing and operating pressure tests for piping.

• Cleaning and preservation of new and disturbed surfaces.

• The document references "Standard Items (FY26)" and various NAVSEA drawings for detailed specifications.

• It also lists Government Furnished Material (GFM) and required materials for the job.

• The document details specific procedures and requirements for the work, including safety precautions and the use of specialized tools and equipment.

• A "REPORT" is required detailing inspection results and repair recommendations.

• Not specified in this document.

• Initial condition notes indicate wear and distortion on 40 tie-down sockets.

• Cleaning of adjacent tanks and engine rooms are covered by separate ICNs.

• Marine chemist inspection is covered by ICN 38NBA11006_A01.

Statement of Work (SOW) / Performance Work Statement (PWS)

This document outlines the requirements for inspecting and preserving the fuel tanks in the 2-46-1-F and 2-46-2-F sections of the LCU-1651 NBU-7 vessel.

• Title: Fuel Tank in 2-46-1-F and 2-46-2-F; inspect and preserve.

• Location: Starboard Fuel Tank (2-46-1-F) "CRITICAL COATED AREA" and Port Fuel Tank (2-46-2-F) "CRITICAL COATED AREA". Also includes Equipment & Repair Parts Stores (2-40-0-A).

• Identification: Two fuel tanks, each with a capacity of 1,775 gallons.

• Tasks: Includes cleaning, rendering dry, and preserving the interior surfaces of the fuel tanks. Requires visual inspection for structural integrity, deterioration, pitting, and damage.

• A Marine Chemist certificate must be submitted.

• Requirements of ENCLOSURE (T) for cleaning and preservation must be accomplished.

• A report detailing the results of the inspection and cleaning must be submitted.

• Waste liquid removal and disposal procedures must be followed, including coordination with the SRF-JRMC Detachment Sasebo ESH Division.

• POP Start Date: 2/02/2026

• POP End Date: 9/30/2026

• Anticipated Award Date: 12/04/2025

• Production Completion Date: 8/24/2026

• Place of Performance: SASEBO (PREPARING ACTIVITY)

• Coordination with the ship's Damage Control Assistant (DCA) is required for fluid off-loading or transferring.

• Government Furnished Materials (GFM) are listed, including various gaskets, nuts, washers, and metal sheets.

• Ship's force will provide system fluid.

Statement of Work (SOW) / Performance Work Statement (PWS)

To replace the degraded mesh cover on a ventilation duct for the FWD Engine Room of the LCU-1651 NBU-7.

• Remove the existing mesh cover.

• Fabricate and install one new steel mesh cover for the Vaneaxial Fan, located in Section 1.2 of the FWD Engine Room.

• Accomplish cleaning and preservation of new and disturbed surfaces to match surrounding areas.

• Witness visual inspection of the replaced mesh cover by Ship's Force.

• A condition report listing the results of the visual inspection must be submitted to the Supervisor.

• POP Start Date: 2/02/2026

• POP End Date: 9/30/2026

• Anticipated Award Date: 12/04/2025

• Production Completion Date: 10/21/2026

• Location: FWD Engine Room (2-50-0-E), SASEBO.

• Guidance for fabrication is provided in reference 2.2.

• Cleaning and preservation requirements are detailed in reference 009-32 of 2.1.

• Government Furnished Material: None.

Statement of Work (SOW) / Performance Work Statement (PWS)

This document details the "Remote Push Button Cable for Bow Ramp Winch; replace" job specification for the LCU-1651 NBU-7.

• Location of Work: Weather Deck, Frame 13, STBD Wingwall Control Station and Ramp Handling Machinery Compartment.

• Items to be Replaced:

  • One (1) Remote Push Button for Bow Ramp Winch (MFR: DRS Power and Control Technologies).
  • One (1) Motor Controller for Bow Ramp Winch (MFR: Cutler Hammer Inc.).
  • One (1) Electric Cable connecting the push button and motor controller (Cable Circuit No.P-408-G, Cable Type LSMSCU-7, Approx. 50 FT).

• Requirements: Remove existing cable and install new cable.

• Inspection: Inspect the push button for damage, deterioration, and electrical defects.

• Installation: Cable installation, penetration, cableway, cable tag, and wire marking must be in accordance with MIL-STD-2003B.

• Connections: Connect and verify connections using provided guidance documents.

• Testing: Accomplish a local air hose test of each penetration and a continuity test on the new electric cable.

• Anticipated Award Date: December 4, 2025 - May 1, 2026

• POP Start Date: February 2, 2026

• POP End Date: September 30, 2026

• Production Completion Date: August 29, 2026

• Initial Condition: The existing electrical cable for the remote switch was found to be degraded.

• Government Furnished Material (GFM): Includes electrical cable, strapping, buckles, rubber channel, and packing assemblies.

Solicitation / RFP / RFQ

This document is a Request for Quotation (RFQ) for repair and alteration of vessels (MARV). The award will be a Firm-Fixed-Price job order under an existing Master Ship Repair Agreement (MSRA) or Agreement for Boat Repair (ABR) in the Japan Region. Firms must possess a current MARAV to be eligible for award, unless there is adequate time for the Navy to assess and execute a new MARAV.

The solicitation outlines specific repair tasks, including:

• Inspect and replace Vehicle Deck Lashing Socket

• Inspect and preserve Fuel Tank

• Replace Fuel Oil Fill Shore Connection Piping

• Replace Mesh Cover on Ventilation Duct

• Replace Crew Berth

• Replace Remote Push Button Cable for Bow Ramp Winch

• Clean Fresh Water Tank and Piping

• The contract will be a Firm-Fixed-Price job order.

• The period of performance for each line item is from 01 June 2026 to 30 September 2026.

• Payment will be made in Japanese Yen (JPY), with an exchange rate of JPY 150.4415 per USD 1.00.

• Quotations are due by 01 May 2026.

• Award will be made to the responsible offeror whose total offer is most advantageous to the Government, considering price and other factors.

• The primary evaluation factor is Price (Lowest Total Price).

• The solicitation includes provisions for prompt payment discounts.

• Award is restricted to firms possessing a current MARAV (MSRA or ABR) in the Japan Region.

• Firms without a current MARAV may be eligible if there is sufficient time for the Navy to assess and execute a new MARAV.

• Non-MARAV holders can request an application package via email: flcy_msra_abr_group@us.navy.mil.

• The document includes standard FAR and DFARS clauses related to contract administration, inspection, quality assurance, payment, and cybersecurity requirements (CMMC).

• Specific instructions for electronic submission of payment requests via Wide Area WorkFlow (WAWF) are provided.