Camera Security Systems

Questions & Answers / Clarifications

This document provides responses to vendor questions regarding Solicitation FA301626Q0025 for Camera Security Systems for Buildings 10251, 10253, 10255, 10261, 10263, & 10265.

• Site Visit List: Contractors who attended both site visits should have received a copy of the sign-in sheet.
• Extension Request: No extension will be granted for the Q&A posting due to the number of questions and Memorial Day holiday.
• Period of Performance/Dates: Expected performance period and project start/end dates are dependent on the contract award date.
• PTZ Cameras: PTZ cameras are located on the Bldg. 10255 3rd floor as outside cameras.
• Switches: There are 12 switches required (two per building for Bldgs. 10255, 10263, 10265, 10261, and 10251), not 14 as initially questioned.
• GFE: No Government Furnished Equipment (GFE) is listed for this requirement.
• Hardware Compliance: All hardware must be TAA and NDAA compliant.
• Remote Access: Remote access for final camera aiming is permitted if needed.
• Cybersecurity: The system must be standalone and not connect to the Air Force network. TAA and NDAA compliance are required.
• Telecom Closets: Telecom closets are environmentally conditioned and properly ventilated for PoE switching equipment. Electrical load capacity is sufficient.
• Grounding/Surge Protection: No additional grounding or surge protection is required for exterior cameras beyond what is in the SOW.
• Network Support: VLAN configuration, switch programming, IP addressing, and network integration are fully the contractor's responsibility (turnkey system).
• Fiber Transport: Existing fiber runs between buildings and to the maintenance hole in the courtyard. Existing fiber can be used if connections are good; otherwise, it will need to be replaced. Contractors should factor worst-case options for cable length and potential pathway issues.
• Work Hours: Work must be performed between 0700 – 1600 when students are not in the buildings.
• Cable Certification: Cable certification and test reports are required at project closeout, demonstrating a fully operational system.
• Penetration/Drilling: No existing approved process for unforeseen routing conditions; additional approval may be requested if needed.
• Onsite Discovery: Additional onsite discovery time after award is permitted if hidden infrastructure conditions are encountered, but the awarded quote amount is final.
• Pathway Blockages: Contractors must factor worst-case options for blocked or unusable pathways; change orders will not be approved for additional conduit or alternative routing.
• Room Identification: Main computer rooms and MDF/IDF/TR locations are listed in the SOW and building layout.
• Dropped Ceilings: Dropped ceilings exist in all installation areas.
• Wage Determination: A wage determination is not attached to this requirement.
• Cable Length: The government will change the cable length to 12,000 FT per building in the final SOW. Contractors should factor worst-case options.
• Camera Count: The correct camera count is 222 total cameras, with 4 PTZ cameras considered outdoor, leaving 218 indoor cameras.
• Audio Requirement: Audio will not be needed for this project and will be removed from the final SOW.
• Existing Mounts: Existing vertical wall mount racks can be reused.
• Access Points: New access points can be made if needed, subject to prior approval.
• Lift for PTZ: Contractors must supply their own lift for outdoor PTZ camera installation.
• Backup Power: Contractors will supply a 30 Amp circuit for the UPS.
• CMMC: CMMC requirements do not apply as the system is standalone and not connected to Air Force internet.

These clarifications address numerous technical and logistical questions, impacting how bidders should scope their proposals, particularly regarding network infrastructure, cable lengths, camera types, and compliance requirements. Bidders should ensure their quotes reflect these clarifications, especially concerning the turnkey nature of the system and the responsibility for all network components and pathways.

Questions & Answers / Clarifications

This document contains questions and answers related to Amendment 1 for the Camera Security Systems for Joint Base San Antonio (JBSA) Lackland. It serves to clarify details for potential bidders.

This attachment is a template for questions and answers and does not contain specific Q&A content. It lists 20 numbered questions, but no actual questions or answers are provided within the document text.

As this document is a template with no specific content, it does not directly impact the solicitation requirements, due dates, or submission rules. Bidders would typically use this template to submit their questions.

Amendment / Modification

This amendment (Amendment 1) to the solicitation extends the response due date from April 30, 2026, to June 2, 2026. It also incorporates several other documents and clauses:

• Attachment 1: Statement of Work (SOW) - Amendment II, dated April 28, 2026.

• Attachment 3: Salient Characteristics - Amendment II, dated April 28, 2026.

• Attachment 4: Questions and Answers, dated April 23, 2026.

• Attachment 5: Questions and Answers Template.

• RFO Clause 52.222-90: Addressing DEI Discrimination by Federal Contractors.

• Solicitation/Contract Form: The Small Business Type remains "Service-Disabled Veteran-Owned Small Business." The Response Due Time is now 10:00 AM, and the Response Due Date is June 2, 2026.

• Description/Specifications/Statement of Work: Refers to Attachment 1 - Amendment II, SOW dated April 28, 2026.

• Contract Clauses: Includes an addendum to FAR 52.212-1, "Instructions to Offeror - Commercial Items (FEB 2026)", with modifications to paragraphs (a)(6), (a)(6)(A), and (a)(7) regarding evaluation factors, pricing data submission, and quote submission methods. It also tailors FAR 52.212-4, "Contract Terms and Conditions (NOV 2023)", regarding changes. A new clause, 52.222-90, "Addressing DEI Discrimination by Federal Contractors," is incorporated.

• The proposal submission deadline has been extended to June 2, 2026, at 10:00 AM CDT.

• Quotes must be submitted via email to parie.reynolds@us.af.mil, with belinda.tindal.1@us.af.mil as a secondary contact.

• The evaluation criteria and submission requirements have been updated, including specific instructions for pricing data and identifying exceptions to terms and conditions.

Statement of Work (SOW) / Performance Work Statement (PWS)

To remove existing camera security systems and install new, stand-alone network security camera systems in multiple buildings at JBSA Lackland, TX.

• Replace 219 existing cameras with 222 new "High-Definition Transport Video" cameras across buildings 10251, 10253, 10255, 10261, 10263, and 10265.

• Install new network switches, racks, and uninterruptible power supplies (UPS) in designated server rooms.

• Install new CAT6 lines for camera inputs and ensure connections convert to Power over Ethernet (PoE).

• Design, deliver, and fully install the security monitoring system.

• Ensure cameras are suitable for low/no light conditions and outdoor cameras are weather-protected.

• Replace three workstations and eight 43-inch LED TVs/Smart TVs in Building 10253/Rm 113.

• The system must be stand-alone and not touch the Air Force network; no classified or sensitive data is to be used.

• Provide training on system use, backup, and camera operation.

• Old TVs and workstations are to be turned over to the Government.

• NVRs must record 24/7/365 and store video for at least 30 days.

• Cameras must be of sufficient quality to see in low/no light.

• Outdoor cameras require all-weather protection.

• The work is for buildings located at JBSA Lackland, TX.

• Work hours are Monday-Friday, 7:30 a.m. to 4:30 p.m. CDT, excluding Federal holidays, with potential for government-approved work outside these hours.

• Equipment specifications are detailed, including camera types (indoor/outdoor dome, pendant), NVRs, workstations, TVs, switches, UPS, and cabling.

• Contractor must comply with commercial industry and Telecommunications Systems Cabling Standards.

• Contractor is responsible for site maintenance, cleanup, freight, unpacking, delivery, and installation.

• Manufacturer and standard commercial warranties are required.

• Final inspection and acceptance by a Government representative.

• No changes to the scope without Contracting Officer modification.

Amendment / Modification

This document, Amendment II to Solicitation FA301626Q00250001, details the "Salient Characteristics" for the Camera Security Systems requirement. It outlines the specific hardware, software, and services required for a complete, turn-key solution.

This amendment specifies the required components and their performance characteristics, including:

• Background: Identifies the location (JBSA Lackland, TX) and the need to replace end-of-life camera systems.
• List of Required Equipment: Details quantities and types of equipment, including:
  • Enterprise Edition camera connection licenses
  • Network Video Recorders (NVRs)
  • Workstations
  • Surface Mount Indoor Dome Cameras
  • Outdoor Dome Cameras
  • Outdoor Ceiling Mounts
  • Outdoor Pendant Mount Adapters
  • Outdoor Dome Covers
  • 43" 4K LED TVs
  • Universal Low Profile Wall Mounts
  • Smart Managed Power over Ethernet + Switches
  • CAT6A Plenum Cable
  • Uninterruptible Power Supplies (UPS)
  • Small Form-factor Pluggable (SFP) modules
  • 6U Wall Mount Rack Enclosures
• Performance Characteristics: Specifies detailed technical requirements for each component, such as resolution, storage capacity, compatibility standards (e.g., ONVIF), power requirements, physical form factors, and environmental resistance.

This amendment provides critical technical specifications that bidders must meet. Vendors should review these detailed requirements carefully to ensure their proposed solution aligns with the government's needs. No changes to proposal deadlines or submission instructions are mentioned in this amendment.

Questions & Answers / Clarifications

This document provides responses to questions submitted by potential bidders regarding the Camera Security Systems solicitation for JBSA-Lackland.

• Cabling: New Cat6 cabling is required. Existing coaxial cabling will be removed and replaced. Existing pathways should be used where possible, but new conduit may be needed in some areas. Cat6A or greater is required.
• Cameras: IP network cameras are required, not TVI analog cameras. Existing cameras are not TAA and NDAA Section 889 compliant and must be replaced. Pan/Tilt/Zoom capability is desired for cameras.
• Equipment: NVRs are required for recording. The system must be TAA and NDAA Section 889 compliant. "Or Equal" equipment substitutions are allowed if they meet or exceed specifications.
• Installation: The old system must be decommissioned and removed immediately. Contractors must supply their own lifts if needed. Access to student storage rooms/closets is permitted if needed. Installation is typically expected to take 120 days.
• Site Information: Buildings are primarily hard-lid with hatches for cabling. Existing conduit should be used where possible. Power is stable. No existing as-built documentation or wiring diagrams are available.
• Project Scope: The project involves replacing existing camera security systems with new, stand-alone network security camera systems. The government is seeking a turnkey security system.

These clarifications address technical requirements, material specifications, installation procedures, and site conditions, which will impact how bidders prepare their proposals and technical approaches. Key details regarding cabling types, camera technology, and compliance requirements have been refined.

Questions & Answers / Clarifications

This document provides responses to vendor questions regarding the "Camera Security Systems" solicitation (FA301626Q0025) for JBSA-Lackland.

• Cabling: New Cat6 cabling is required. Existing conduit can be used where possible, but new conduit may be needed for exposed areas. Existing coaxial cable will be removed and replaced with Cat6. Cat6A cable is acceptable.
• Cameras: The system requires IP network cameras, not TVI analog cameras. Existing cameras are not TAA and NDAA Section 889 compliant and must be replaced. Pan/Tilt/Zoom functionality is desired for cameras.
• Equipment: NVRs are required (not DVRs/XVRs). "Or Equal" equipment substitutions are allowed if they meet or exceed Salient Characteristics. All equipment must be TAA and NDAA Section 889 compliant.
• Installation: Existing pathways should be used where possible. Minor drilling for racks and TV mounts is authorized; larger modifications require CE approval. The contractor is responsible for providing their own lift if needed. UPS backup time is 30 minutes.
• Site Access: Initial installation access, once granted, should be valid for the project duration unless the project extends significantly. After-hours work may be permitted at no additional cost with Government approval.
• Documentation: As-built documentation and wiring diagrams for the original system are not available.
• Project Scope: The project involves replacing existing camera security systems with new, stand-alone network security camera systems. The project is expected to take approximately 120 days, with potential for extensions.

This Q&A document clarifies technical requirements, material specifications, installation procedures, and site access protocols, which bidders should consider when preparing their proposals. It confirms the preference for IP cameras, the requirement for new cabling, and the compliance standards (TAA and NDAA Section 889).

Amendment / Modification

This document is Amendment 1 to the Statement of Work (SOW) for the Camera Refresh project at JBSA Lackland AFB. It details the specific requirements for the design, delivery, and installation of a new stand-alone network security camera system across multiple buildings.

• Project Scope: Outlines the contractor's responsibility to remove existing camera systems and install new, stand-alone network security cameras in buildings 10251, 10253, 10255, 10261, 10263, and 10265.
• Deliverables: Includes replacing 219 existing cameras with 222 new "High-Definition Transport Video" cameras. It also specifies the replacement of three workstations and eight 43-inch LED monitors in Building 10253.
• System Requirements: Mandates that the new system must be stand-alone and not touch the Air Force network, and must not handle classified or sensitive data. All cables must be marked, and outside cameras must be protected by all-weather shells.
• Equipment Specifications: Details the required equipment, including 222 camera connection licenses, Network Video Recorders (NVRs), workstations, indoor and outdoor cameras, LED TVs, wall mounts, Power over Ethernet switches, CAT6e plenum cable, and Uninterruptible Power Supplies (UPS).
• Camera Locations: Provides extensive lists of specific locations for indoor and outdoor cameras within each building (10251, 10253, 10255, 10261, 10263, and 10265), referencing building layout attachments.
• Work Hours: Specifies standard work hours (7:30 a.m. to 4:30 p.m., Monday-Friday, CDT), with provisions for work on Federal holidays or outside these hours at no additional cost, subject to Government approval.
• General Information: References commercial industry and Telecommunications Systems Cabling Standards, including 13A Standards and UFC 3-580-1.
• Testing and Acceptance: Outlines requirements for system demonstration, testing, and final inspection by a Government representative.
• Warranty: Requires manufacturer and standard commercial warranties for all equipment.

This amendment significantly expands upon and details the scope, deliverables, technical specifications, equipment, and installation locations for the camera refresh project. It supersedes previous information and provides the definitive requirements for bidders.

Amendment / Modification

This document is Amendment 1 to the solicitation FA301626Q0025 for Camera Security Systems. It details the salient characteristics and performance requirements for the proposed camera system.

• Background: Outlines the need for a new camera system at Joint Base San Antonio due to end-of-life equipment.
• List of Equipment: Specifies the quantities and types of equipment required, including:
  • Enterprise Edition camera connection licenses
  • Network Video Recorders (NVRs)
  • Workstations
  • Surface Mount Indoor Dome Cameras
  • Outdoor Dome Cameras
  • Outdoor Ceiling Mounts
  • Outdoor Pendant Mount Adapters
  • Outdoor Dome Covers
  • 43" 4K LED TVs
  • Universal Low Profile Wall Mounts
  • Smart Managed Power over Ethernet + Switches
  • CAT6A Plenum Cable
  • Uninterruptible Power Supplies (UPS)
  • Small Form-factor Pluggables (SFPs)
  • 6U Wall Mount Rack Enclosures
• Performance Characteristics: Details specific technical requirements for each component, including:
  • Enterprise Camera Connection License: Minimum camera connections, VMS capabilities, ONVIF compliance, and video compression standards.
  • Network Video Recorder (NVR): Storage capacity (minimum 64 TB), performance for simultaneous recording/playback, resolution support (up to 7K), and scalability.
  • Workstations: Processor, RAM, video output (dual 4K displays), networking ports, and operating system requirements.
  • Surface Mount Indoor Dome Camera: Resolution (minimum 4 Megapixels), day/night capability, mounting, durability (IK10, IP66/IP67), varifocal lens, frame rate (25/30 fps), image quality features (WDR, Backlight Compensation), power (PoE), and video compression.
  • Outdoor Dome Camera: Resolution (minimum 4 Megapixels), day/night capability with IR illuminators, durability (IK10, IP66), varifocal lens with motorized zoom, image quality features (WDR), frame rate (25/30 fps), image sensor, power (PoE), video compression, and analytics (motion detection).
  • 4K LED Smart TV: Screen size (43-inch class), display type, resolution (4K UHD), refresh rate (60Hz+), connectivity (HDMI, USB, Wi-Fi, Ethernet), and power.
  • Universal Low Profile Wall Mount: Compatibility with 43-inch displays, VESA standards, weight capacity (50 lbs), low-profile design, tilt adjustment, and installation hardware.
  • Smart Managed PoE+ Switch: Port configuration (24+ Gigabit Ethernet, 2 SFP+), PoE+ compliance (30W/port), total PoE budget (370W+), surge protection, performance (non-blocking fabric), MAC address table size, Jumbo Frames support, switching architecture, management features (smart/fully-managed, GUI/CLI, IPv4/IPv6), VLAN support, security features (ACLs, Port Security, IP Source Guard), LLDP, and Energy-Efficient Ethernet.
  • CAT6A Plenum Cable: Standard compliance (ANSI/TIA-568), safety rating (CMP), conductor type (23 AWG solid bare copper).
  • Uninterruptible Power Supply (UPS): Power capacity (600W/1.0kVA), topology (Line-Interactive with AVR), output (Pure Sine Wave, 120V/60Hz), physical form factor, user interface (LCD, audible alarms), management port (USB/Serial), and outlets (battery-backed, surge-protected).
  • 6U Wall Mount Rack Enclosure: Color (Black), weight capacity (200 lbs), adjustable mounting depth (up to 17 inches), construction (heavy-duty steel), lockable door, cable management, ventilation, and hardware.

This amendment provides detailed technical specifications that bidders must adhere to when preparing their proposals. It does not appear to modify proposal deadlines or submission instructions based on the provided text.

Amendment / Modification

This document is Amendment 1 to the Statement of Work (SOW) for the Camera Refresh project at JBSA Lackland AFB. It details the specific requirements for the design, delivery, and installation of a new stand-alone network security camera system across multiple buildings (10251, 10253, 10255, 10261, 10263, and 10265).

Key changes and additions include:

• Replacement of existing cameras with 222 new "High-Definition Transport Video" cameras.
• Installation of new network video recorders (NVRs), workstations, and 43-inch LED monitors.
• Specification of equipment details, including camera types (indoor dome, outdoor dome, outdoor ceiling mount), NVRs, workstations, TVs, switches, UPS, and cabling.
• Detailed location breakdowns for camera placement within each building, specifying floor and exact position (e.g., "south corner of walkway").
• Requirements for the system to be stand-alone and not touch the Air Force network, and to ensure no classified or sensitive data is used.
• Provision of training for system use, backup, and camera operation.
• Specifics on equipment like NVRs needing 24/7/365 recording capability for at least 30 days, and the TVs being 51" above the floor.
• Inclusion of work hours, special conditions, base fire regulations, site maintenance, energy conservation, contract management, records management, testing, inspection, and warranty requirements.

This amendment significantly expands upon the original SOW by providing detailed project scope, project description, specific camera locations per building, equipment specifications, and general information/conditions.

This amendment provides the detailed technical specifications and scope of work necessary for bidders to prepare their proposals. It clarifies the exact requirements for the camera refresh project.

Statement of Work (SOW)

This Statement of Work (SOW) details the requirements for removing existing camera security systems and installing new, stand-alone network security camera systems in multiple buildings at Joint Base San Antonio (JBSA) Lackland, TX.

• System Replacement: Replace 219 existing cameras with 222 new "High-Definition Transport Video" cameras across buildings 10251, 10253, 10255, 10261, 10263, and 10265.

• New Installations: Install additional cameras where none currently exist.

• Workstations & Monitors: Replace three workstations and eight 43-inch LED monitors in Bldg. 10253/Rm 113. Existing TVs and workstations are to be turned over to the Government.

• Network Video Recorders (NVRs): Install four NVRs in Bldg. 10253/Rm 113.

• Infrastructure: Install new CAT6 lines and convert camera connections to Power over Ethernet (PoE).

• Training: Provide training and instructions for system use, backup, and camera operation.

• Cameras must be capable of clear visibility in low/no light conditions.

• Outside cameras must be protected by all-weather shells.

• NVRs must record 24/7/365 and store feeds for at least 30 days, with capability for external storage.

• The system must be stand-alone and not touch the Air Force network.

• No classified or sensitive data should be used with the system.

• No unmarked cables are permitted.

• Location: Joint Base San Antonio (JBSA) Lackland, TX, specifically Buildings 10251, 10253, 10255, 10261, 10263, and 10265.

• Work Hours: Monday through Friday, 7:30 a.m. to 4:30 p.m. CDT, excluding Federal holidays. Work may be permitted on Federal holidays or weekends at no additional cost if approved by the Contracting Officer.

• Cabling Standards: Projects must meet commercial industry and Telecommunications Systems Cabling Standards, referencing 13A Standards and UFC 3-580-1.

• Site Maintenance: Maintain neat, clean, and safe work areas; remove all trash and debris.

• Energy Conservation: Adhere to prevailing energy conservation practices.

• Contract Management: All changes require modification by the Contracting Officer.

• Records Management: Manage data according to AF Records Management procedures.

• Testing: Conduct system demonstrations for Government observation.

• Inspection & Acceptance: Final inspection by Mr. Timothy Donelson (37 TRSS).

• Warranty: Provide manufacturer and standard commercial warranties, contact information, and operational manuals.

• Attachment 1: Building Layout

• Attachment 2: Salient Characteristics

Form / Attachment / Pricing Sheet

This document, "Salient Characteristics Attachment 3," details the specific technical requirements and quantities for a camera security system. It serves as a critical attachment to a solicitation, outlining the "what" and "how much" for potential bidders to understand the scope of the procurement.

• Background: Identifies the need to replace an end-of-life camera system in specific buildings at JBSA Lackland, TX, supporting the 343 TRS.
• Itemized List of Equipment: Provides a comprehensive list of required items and their quantities, including:
  • Enterprise Edition camera connection licenses
  • Network Video Recorders
  • Workstations
  • Indoor and Outdoor Dome Cameras
  • 4K LED TVs and associated wall mounts
  • Power over Ethernet switches
  • CAT6e plenum cable
  • Engineering, Installation, and Commissioning Services
  • Uninterruptible Power Supplies (UPS)
  • Small Form-factor Pluggable (SFP) modules
  • Wall Mount Rack Enclosures
• Detailed Salient Characteristics: For key components like Network Video Recorders, Workstations, Indoor Dome Cameras, and Outdoor Dome Cameras, the document specifies critical technical attributes such as:
  • Storage capacity (e.g., 64 TB for NVRs)
  • Resolution (e.g., 4K, 7K/30MP)
  • Compression types (H.264, H.265)
  • Connectivity (e.g., Ethernet, PoE)
  • Power requirements
  • Physical dimensions and weight
• Point of Contact: Provides contact information for Detra Whitfield for any inquiries.

This attachment is crucial for bidders to:

• Determine their capability to meet the specified technical requirements for each component.
• Accurately price their proposals based on the detailed quantities and specifications.
• Understand the scope of the system being procured, including the number and types of cameras, recording devices, and supporting infrastructure.

Form / Attachment / Pricing Sheet

This document provides building layouts for various facilities at JBSA-Lackland AFB, specifically detailing the placement of indoor cameras, stairs, and north orientation for Buildings 10251, 10253, 10255, 10261, 10263, and 10265.

• Floor plans for each specified building, broken down by floor.
• Location indicators for indoor cameras, stairs, and server rooms (where applicable).
• Numbered callouts corresponding to specific camera or equipment locations.
• Scale indicators in feet for each floor plan.

This attachment is crucial for bidders involved in security system installation, maintenance, or upgrades. It visually outlines the areas requiring camera coverage, potential installation points, and the overall physical environment of the facilities. Bidders should use these layouts to understand the scope of work, estimate material and labor needs, and plan for site-specific requirements related to camera placement and network infrastructure within these buildings.

Solicitation / RFP / RFQ

This is a combined synopsis/solicitation (Request for Quote - RFQ) for commercial items to procure the installation of new stand-alone network security camera systems in six buildings (10251, 10253, 10255, 10261, 10263, and 10265) located at Joint Base San Antonio (JBSA) Lackland, TX. The government is procuring these services to upgrade existing security camera systems.

• Installation of new stand-alone network security camera systems.

• Removal of existing camera security systems.

• Performance will be in accordance with the Statement of Work (SOW) dated 26 January 2026 (Attachment 1).

• Specific equipment includes indoor cameras, enclose racks, PoE+ switches, UPS, CAT 6 wiring, and camera connection licenses, as detailed in the "Supplies or Services & Prices or Costs" section for each building.

• Contract Type: Firm Fixed Price (FFP).

• Period of Performance: To be determined at time of award.

• Estimated Value: Not explicitly stated, but the SBA size standard is $25M.

• Quotes must be emailed to Parie Reynolds (parie.reynolds@us.af.mil) and Lance Watters (lance.watters.1@us.af.mil).

• Submission Deadline: Thursday, 30 April 2026, by 1:00 p.m. CDT.

• Questions Deadline: Thursday, 16 April 2026, by 1:00 p.m. CDT.

• Evaluation Criteria: Lowest Priced, Technically Acceptable (LPTA) basis. Award will be made to the responsible vendor whose quote is the lowest evaluated price among technically acceptable quotes.

• Quotes must be effective for 90 days after submission.

• This requirement is a 100% total set-aside for Service Disabled Veteran Owned Small Business (SDVOSB) concerns.

• Offerors must hold NAICS Code 561621 and meet the $25M size standard.

• Registration in the System for Award Management (SAM) is mandatory for award.

• A site visit is scheduled for Tuesday, 7 April 2026, at 10:00 a.m. CDT. Attendance is highly encouraged.

• Offerors must contact Parie Reynolds to obtain installation access passes for the site visit by 24 March 2026.

• Funds are not currently available for this requirement; no award will be made until funds are available.