P993/995, F-35 Aircraft Sustainment Center and Composite Repair Facility located at the Marine Corps Air Station (MCAS) Cherry Point, NC

Amendment / Modification

This amendment, Number 0009, modifies solicitation N4008526R0002 for the DESIGN-BID-BUILD, P993/995 F35 SUSTAINMENT CENTER & COMPOSITE REPAIR FACILITY at MARINE CORPS AIR STATION, CHERRY POINT, NORTH CAROLINA.

• Added "Amendment 0009 PPI Responses" as an attachment under Section 00 73 00 - Supplementary Conditions.

• The proposal due date of 27 May 2026 at 2:00 P.M. EDT remains unchanged.

• No further Pre-Proposal Inquiries (PPI) will be accepted.

Questions & Answers / Clarifications

This document contains responses to pre-proposal inquiries regarding the "P-993 F-35 Sustainment Center" solicitation.

• CMMC Level 2 Requirement: A significant concern was raised regarding the burdensome CMMC Level 2 certification requirement for subcontractors, potentially hindering the ability to meet the 40% small business participation target. The government's response is "Propose to RFP," indicating no immediate change to the requirement.
• Analytical Data for Water/Soil Conditions: A question was posed regarding the availability of analytical data for water and soil conditions at the P-995 or P-993 sites concerning contamination. The government's response is "PENDING RESPONSE."
• Small Business Participation Target: A question asked if the small business participation target could be reduced from 40% to 20% due to the CMMC requirement's impact on local small businesses. The government's response is "Propose to RFP."
• CMMC Unique Identifiers Submission: Clarification was requested on where to submit CMMC unique identifiers (CMMC UIDs). The government directed this information to be provided in the price proposal form.
• Historic Small Business Utilization: Inquiries were made regarding the submission of projects in progress for historic small business utilization and the evaluation of "ACTUAL" columns when "GOAL" columns are blank. The government confirmed that projects in progress with completed ISRs can be submitted and provided clarification on how to complete the form when goals were not established.
• Thermal Monitoring Control Plan: A request was made for a modified, performance-based approach in lieu of full thermal monitoring for mass concrete, citing that full monitoring is not typically required when thermal performance can be controlled through mix design and placement procedures. The government's response is "PENDING RESPONSE."

Several questions highlight potential challenges for small businesses due to CMMC requirements and inquire about reducing participation targets. The government's consistent "Propose to RFP" response suggests these issues may need to be addressed within the proposal itself rather than through solicitation changes at this stage. One question regarding CMMC UID submission was clarified, directing bidders to the price proposal form. Responses to other critical questions, such as analytical data and thermal monitoring, are pending.

Questions & Answers / Clarifications

This document contains responses to Pre-Proposal Inquiry (PPI) questions related to the solicitation for the P-993 F-35 Sustainment Center project.

• CMMC Level 2 Certification: The government is reviewing a request to reduce the small business participation target from 40% to 20% due to the burden of CMMC Level 2 certification on local small businesses.
• Analytical Data for Site Conditions: The government is reviewing a request for analytical data regarding water and soil conditions at the P-995 or P-993 sites concerning contamination.
• Small Business Participation Target: A request was made to revise the small business target goal to 10% due to the burden of CMMC Level 2 certification on subcontractors.
• CMMC Unique Identifiers: Clarification was sought on where to provide CMMC unique identifiers (CMMC UIDs) in the proposal submission.
• Land Use Control Plans: A Land Use Control plan will be required for the project and coordination with MCAS Cherry Point is necessary for submittal requirements.
• CMMC Level 2 Consideration: A request was made to apply the consideration for CMMC Level 2 requirements to this project, allowing contractors who do not yet meet it to access restricted documents if they confirm a BASIC Confidence Level in SPRS.
• Paint Booth Delegated Design: Clarification was requested regarding the delegated design responsibilities, deliverables, and specifications for paint booth systems.
• Utility Connections for Collateral Equipment: Multiple questions address the definition and responsibility for utility connections (e.g., electrical, data, grounding, cooling, exhaust, vacuum) for collateral equipment, particularly for ovens and paint booths.
• Secure Area Requirements: Extensive clarification is provided regarding security requirements for the Secure Construction Site and Secure Area, including personnel vetting, access control, material handling, RF testing, and documentation.

These clarifications and responses may impact proposal preparation, submission requirements, and understanding of specific project requirements, particularly concerning CMMC compliance, small business participation, and security protocols.

Amendment / Modification

This amendment (0008) to solicitation N4008526R0002 for the DESIGN-BID-BUILD P993/995 F35 SUSTAINMENT CENTER & COMPOSITE REPAIR FACILITY at Marine Corps Air Station, Cherry Point, North Carolina, makes the following changes:

• Proposal Due Date: The proposal due date of May 27, 2026, at 2:00 PM EDT remains unchanged.

• Revised Specifications (P993 - CUI): Several sections of the specifications have been revised:

  • Contamination laboratory results have been added to section 01 57 19.01 20.
  • References to SSPC QS 1 and Certified Industrial Hygienist/Qualifications of Coating Contractors have been removed from sections 09 97 13.16 and 09 97 13.27.
  • Section 31 00 00 has been revised to allow a maximum of 20 percent passing the No. 200 sieve.
  • Seismic Design Category has been corrected to B in section 33 16 15.
  • Section 41 22 13-55 has been replaced entirely and includes a description of the Runway Conductor Bar.

• Revised Drawings (P993 - CUI): Several drawings have been revised:

  • Changes to water service lines and yard hydrants in drawings CU004 and CU115.
  • Corrections to OWS-3 Label and adjustments to invert on SS18 in CU220.
  • Corrections to OWS-1 Label and IW04/IW05 rim elevations in CU240.
  • Corrections to blowoff sizes in CU242 and CU242.
  • Corrections to IW04/IW05 rim elevations and IW04 type in CU620.
  • Corrections to fittings W29 and W30 to yard hydrant in CU630.
  • Changes to water service size and electrical equipment locations in CU700.
  • Bypass change to below ground in CU701.
  • Addition of size label to 12" overflow pipe in CU801.
  • Corrections to electrical equipment locations in ES114.
  • Updates to elevator receptacles per UFC 3-490-06 section 6-3 in EP403.

• Pre-Proposal Inquiry (PPI) Responses: Additional PPI responses are attached separately. No further PPIs will be accepted.

• Section 00 22 16 - Supplementary Instructions to Proposers

• Specifications (various sections related to P993)

• Drawings (various drawings related to P993)

• Section 00 73 00 - Supplementary Conditions (new attachments added)

No changes to the proposal due date or time. Bidders must review the revised specifications and drawings for updated requirements.

Amendment / Modification

• The proposal due date has been extended from May 20, 2026, to May 27, 2026, at 2:00 P.M. EDT.

• Minor revisions have been made to the EVALUATION FACTORS FOR AWARD.

• A note states that no additional PPIs (Pre-Proposal Inquiries) will be accepted.

• Section 00 00 00 - Procurement and Contracting Requirements (Response Due Date)

• Section 00 22 00 - Supplementary Instructions (Proposal due date and Evaluation Factors for Award)

• The deadline for proposal submissions has been extended to May 27, 2026.

• The evaluation factors for Segment II have been clarified: Factors 5 (Management Approach & Schedule) and 6 (Small Business Utilization) are of equal importance to each other and, when considered together, are approximately equal in importance to the price for construction services. For Segment I, the evaluation factors remain Corporate Experience, Pre-Construction Services Approach, Safety, Past Performance, and Price for Pre-Construction Services.

Amendment / Modification

This document, Amendment 0006, pertains to the "F-35 Sustainment Center" project at MCAS Cherry Point, NC. It includes updates and revisions to the original solicitation documents. Specific details of the changes are not provided in the document title or metadata, but amendments typically involve clarifications, modifications to scope, or adjustments to contract terms.

Not specified in the provided metadata.

Not specified in the provided metadata. Bidders should review the full amendment for any impact on proposal deadlines, requirements, or evaluation criteria.

Amendment / Modification

This document is Amendment 0006 to the P993 specifications, specifically "Addendum No. 1_Div 01". It lists the contract drawings for the project.

This amendment affects the "P-993 LIST OF DRAWINGS" section of the project specifications.

Forms / Attachments / Pricing Sheets

This document contains boring logs (BB101, BB105, BB106, DB-01, DB-02, DB-03) which detail subsurface soil conditions encountered during geotechnical investigations. These logs are critical for understanding the ground conditions at the project site.

Each boring log includes:

• Boring number and location (Northing, Easting, Latitude, Longitude)
• Surface elevation and vertical datum
• Date drilled and drill method
• Soil stratigraphy with descriptions (e.g., Silty SAND, Clayey SAND, Lean CLAY)
• Material properties (e.g., density, moisture content)
• Penetration resistance (blows/foot)
• Estimated depth to groundwater (SHWT)
• Any relevant comments or limitations

These boring logs provide essential geotechnical data. Bidders should review this information to understand the subsurface conditions, which will impact foundation design, excavation, dewatering, and overall construction feasibility and cost for the F-35 Sustainment Center project at MCAS Cherry Point, NC.

Questions & Answers / Clarifications

This document contains responses to pre-proposal inquiries regarding the RFP for the P-993 F-35 Sustainment Center. It addresses vendor questions on various aspects of the solicitation, including CMMC requirements, small business participation, site conditions, and technical specifications.

• CMMC Level 2 Requirement: Vendors questioned the burden of CMMC Level 2 certification on small businesses and its impact on meeting the small business participation target. The government indicated that P-993 drawings and specifications have been reissued without CUI designation via Amendment 0006, and Division 1 specifications for P-993 and P-995 have also been reissued without CUI designation.
• Small Business Participation: A question was raised about reducing the small business participation target from 40% to 20% due to CMMC requirements. The government's response is pending.
• Analytical Data for Contamination: Vendors requested analytical data for water and soil contamination at P-995 and P-993 sites. The government's response is pending.
• Firestopping Contractor Qualifications: Clarification was sought on whether the project is eligible for an alternative firestopping contractor qualification pathway (Option B) instead of the full FM 4991/UL certification (Option A), given regional unavailability. The government confirmed that contractors must either receive FM/UL certification or be certified by the firestopping manufacturer through an accredited program.
• Nitrogen System: A question regarding pipe and fittings materials for the nitrogen system was answered, stating that Sheet P-505, Detail B1 reflects aluminum for the piping material.
• Batch Plant: In response to a question about power and water availability for a batch plant, the government confirmed a location at the south end of DELTA Taxiway with existing utility infrastructure.

Several clarifications and reissues of documents (drawings and specifications) have been made, particularly concerning CUI designations and CMMC requirements, which may affect proposal preparation and subcontractor eligibility. Some responses are still pending, indicating potential for further adjustments or clarifications.

Amendment / Modification

This document is Amendment 0006 to the solicitation.

This amendment pertains to drawing file 1786799dwg09of28Volume1Part-9.pdf.

No specific impact on submission deadlines or requirements is detailed in this amendment's metadata.

Amendment / Modification

This document is Amendment 0006 to the solicitation.

This amendment pertains to Volume 1, Part 6 of the solicitation documents.

No specific impact on proposal deadlines or requirements is detailed in this amendment's metadata. Further review of the amendment content would be necessary to determine any changes to submission instructions, requirements, or evaluation factors.

Amendment / Modification

This document is Amendment 0006 to the solicitation. It contains drawing files, specifically "1786799dwg01of28Volume1Part-1r1.pdf", which is a large PDF file (34,807,737 bytes) posted on May 5, 2026.

This amendment likely impacts the drawings and specifications referenced in the original solicitation.

No changes to proposal deadlines or evaluation factors are mentioned in this amendment summary. Bidders should review the attached drawing file for any necessary updates to their proposals.

Amendment / Modification

This document is a "Submittal Register" which lists various submittals required for the "NAVFAC P993 F-35 Sustainment Center" project. It details the "Description" of each item submitted, the "Specification Section" it pertains to, and various "Contractor Action" and "Approving Authority" dates and codes. The register spans 199 pages and includes a wide range of submittals from "SD-01 Preconstruction Submittals" through "SD-11 Closeout Submittals," covering various construction trades and systems.

This document is a register and does not directly alter specific sections of a solicitation or SOW/PWS. Instead, it serves as a tracking mechanism for all required submittals throughout the project lifecycle.

This register outlines the submittal requirements and tracking for the project. Bidders should consult this document to understand the full scope of submittals needed for compliance and project progression.

Amendment / Modification

This amendment (0006) to solicitation N4008526R0002 for the DESIGN-BID-BUILD, P993/995 F35 SUSTAINMENT CENTER & COMPOSITE REPAIR FACILITY at MARINE CORPS AIR STATION, CHERRY POINT, NORTH CAROLINA, incorporates the following:

• Provides the P993 Submittal Register (attached separately).

• Provides a revised P993 Construction Security Plan (CUI - not posted).

• Provides P993 Division 01 Specifications with CUI removed (attached separately).

• Provides P993 Civil and Landscape Drawings with CUI removed (attached separately).

• Includes additional Pre-Proposal Inquiry (PPI) responses (attached separately).

• Section 00 73 00 - Supplementary Conditions: The "Amendment 0006 PPI Responses" attachment was added.

The proposal due date of 20 May 2026 at 2:00 P.M. EDT remains unchanged.

Amendment / Modification

This document, "Amendment 0006 1786799dwg03of28Volume1Part-3.pdf", appears to be an amendment to a solicitation or related document. The provided OCR text indicates approvals and dates associated with the document, specifically mentioning "FAD APPROVED BY ERIK LEWIS, INFRASTRUCTURE ENG. BRANCH HEAD WITH FRCE 12/16/2025" and "Approved by Sally Torgler, Deputy Director Facilities, with NSWDG, via Email. 15 DEC 2025". The document also contains page numbers such as "123 of 419", "124 of 419", etc., suggesting it is part of a larger set of documents.

Specific sections, clauses, or attachments affected by this amendment are not detailed in the provided OCR text. The document itself is a PDF file named "Amendment 0006 1786799dwg03of28Volume1Part-3.pdf", indicating it is likely a drawing or technical document related to the solicitation.

No information is available in the provided text to determine if proposal deadlines, requirements, or evaluation factors were modified by this amendment.

Amendment / Modification

This document is Amendment 0006 to the solicitation. It contains drawing files related to Volume 1, Part 5 of the opportunity.

This amendment primarily consists of drawing files.

No changes to proposal deadlines, requirements, or evaluation factors are indicated by this amendment.

Amendment / Modification

This document is Amendment 0006 to the solicitation. It contains drawing files related to Volume 1, Part 7 of the opportunity.

• Drawing files for Volume 1, Part 7.

This amendment does not appear to alter submission deadlines, requirements, or evaluation factors. It primarily provides updated or additional drawing files.

Amendment / Modification

This document is Amendment 0006 to the solicitation. It contains drawing files related to the "F-35 SUSTAINMENT CENTER" project at MCAS Cherry Point, NC.

This amendment primarily consists of drawing files (DWG format) that detail various aspects of airfield markings, jointing, spot elevations, and related details. Specific sheets referenced include:

• CT460: Airfield Marking Plan - Overall
• CT461: Airfield Marking Plan
• CT462: Airfield Marking Plan
• CT463: Airfield Marking Plan
• CT464: Airfield Marking Plan
• CT465: Airfield Marking Plan
• CT466: Airfield Marking Plan
• CT467: Airfield Marking Plan
• CT468: Airfield Marking Plan - Bid Option
• CT470: Airfield Jointing & Spot Elevation Plan - Overall
• CT471: Airfield Jointing & Spot Elevation Plan
• CT472: Airfield Jointing & Spot Elevation Plan
• CT473: Airfield Jointing & Spot Elevation Plan
• CT474: Airfield Jointing & Spot Elevation Plan
• CT475: Airfield Jointing & Spot Elevation Plan
• CT476: Airfield Jointing & Spot Elevation Plan
• CT477: Airfield Jointing & Spot Elevation Plan
• CT478: Airfield Jointing & Spot Elevation Plan
• CT479: Airfield Jointing & Spot Elevation Plan
• CT480: Airfield Jointing & Spot Elevation Plan
• CT481: Airfield Jointing & Spot Elevation Plan
• CT482: Airfield Jointing & Spot Elevation Plan
• CT483: Airfield Jointing & Spot Elevation Plan
• CT484: Airfield Jointing & Spot Elevation Plan
• CT485: Airfield Jointing & Spot Elevation Plan - Bid Option
• CT501: Airfield Details (including various sub-details like cleanouts, joints, markings, etc.)
• CT502: Airfield Details
• CT503: Airfield Details
• CT504: Airfield Details
• CT505: Airfield Details
• CT506: Airfield Details
• CT507: Airfield Details (Jet Blast Deflector)
• CT508: Airfield Details (Aircraft Rated Inlet/Manhole)
• CT509: Airfield Details (Double Box Frame Roller Gate)
• CT510: Airfield Details (Powered Heavy Duty Swing Gate)
• CT511: Airfield Details (Runway Closure Markings/Barricades)

This amendment provides updated or additional drawing files. Bidders should review these drawings to ensure their proposals and understanding of the project scope are based on the latest information. No specific impact on proposal deadlines or evaluation factors is mentioned in the provided document metadata, but bidders should verify against the full solicitation if this amendment affects any previously submitted requirements.

Amendment / Modification

This document, Amendment 0006, contains revisions and updates to the original solicitation.

Specific sections, clauses, or attachments that have been modified are detailed within the amendment document.

Potential bidders should review this amendment carefully to understand any changes to proposal requirements, submission deadlines, or evaluation criteria.

Amendment / Modification

This document is Amendment 0006 to the solicitation. It contains drawing files related to the project.

• Drawing files: CU154, CU164, CU200, CU201, CU202, CU203, CU210, CU211, CU212, CU213, CU220, CU230, CU231, CU232, CU233, CU240, CU241, CU242, CU243, CU250, CU260, CU261, CU262, CU263, CU270, CU271, CU272, CU273, CU274, CU275, CU276, CU401, CU402, CU600, CU610, CU620, CU630, CU650, CU700, CU701, CU702, CU800, CU801, CU802, C-500, C-501, C-502, C-503, C-504, C-505, C-506, C-507, C-508, C-509.

This amendment does not appear to modify proposal deadlines, requirements, or evaluation factors, but rather provides updated drawing files.

Amendment / Modification

Amendment 0006 provides supplementary technical and civil engineering documentation for the F-35 Sustainment Center project at MCAS Cherry Point, NC. The amendment includes:

• Geotechnical Data: Detailed boring logs (BB113), Cone Penetration Test (CPT) results (BB114, BB115), and laboratory data summaries (BB116-BB119) detailing soil conditions. It also includes historical boring site locations (BB140).
• Civil Engineering Drawings: Historical boring logs (Sheets BB141-BB143), settlement plans (Sheet B-401), settlement plate details (Sheet B-500), general notes, legends, and abbreviations (Sheets C-001, C-002), and erosion/sediment control sequences (Sheet C-003).
• Demolition Plans: Detailed demolition keynotes and plans (Sheets CD100-CD119) outlining items to be removed or protected, including pavement, structures, vegetation, and utilities. General and utility notes provide specific instructions for site work and utility coordination.

This amendment provides detailed geotechnical and demolition information. Specific sections of the original solicitation, SOW, or PWS are not explicitly identified as changed, but the data impacts the understanding of subsurface conditions and site preparation requirements. Affected civil drawings include settlement plans and historical boring logs.

This amendment does not alter proposal submission deadlines or evaluation criteria. However, the detailed geotechnical and demolition information is crucial for bidders to accurately assess site conditions, develop responsive proposals, and estimate costs for site preparation and demolition activities.

Amendment / Modification

This amendment (0005) to solicitation N4008526R0002 incorporates Pre-Proposal Inquiry (PPI) responses, which are attached separately. Section 00 73 00 - Supplementary Conditions has been updated, and "Amendment 0005 PPI Responses" has been added as an attachment.

• Section 00 73 00 - Supplementary Conditions
• Added Attachment: Amendment 0005 PPI Responses

The proposal due date of 20 May 2026 at 2:00 P.M. EDT remains unchanged. All other terms and conditions of the original solicitation remain in full force and effect.

Questions & Answers / Clarifications

This document contains responses to pre-proposal inquiries (PPI) regarding the P-993 and P-995 projects. It addresses questions related to CMMC Level 2 requirements, small business participation, contamination data, unique identifiers, specifications, materials, testing, commissioning, and other project-specific details.

• CMMC Level 2 Requirements: Several questions address the burden of CMMC Level 2 certification on small businesses and its impact on participation targets. The government's response is often 'PENDING RESPONSE,' indicating further consideration or a need for clarification.
• Small Business Participation: Questions are raised about reducing the small business participation target due to CMMC requirements and the availability of P-995 facility to meet the target. Responses are generally 'PENDING RESPONSE.'
• Specifications and Drawings: Numerous questions seek clarification on discrepancies between drawings and specifications, specific material requirements (e.g., pipe types, coatings, fill materials), and the applicability of certain specifications to P-995.
• Commissioning: Questions focus on the roles of the government's independent commissioning firm versus contractor responsibilities, and the qualifications of commissioning specialists.
• Contractual Scope: Clarifications are sought regarding delegated design responsibilities, the scope of Electronic Security Systems (ESS) as Government Furnished Government Installed (GFGI), and the inclusion of specific items in bid options.

These clarifications and responses may impact bidder understanding of requirements, material choices, cost estimations, and scheduling. The 'PENDING RESPONSE' status on many items indicates that further official guidance may be forthcoming, which bidders should monitor.

Amendment / Modification

This amendment (0004) to solicitation N4008526R0002 modifies the original solicitation and extends the proposal due date.

Key changes include:

• Proposal Due Date Extension: The proposal due date has been extended from April 28, 2026, to May 20, 2026, at 2:00 PM EDT.

• Class Justification & Approval (CJ&A): ML-25-03 FRCS Cherry Point for Johnson Controls has been provided (attached separately).

• Revised Drawings for P995: Several drawings have been revised, including:

  • DWG A-104 (Floor Plan - Area C): Revised opening size for the 'Knockout Panel' for the Large Autoclave.
  • DWG A-201 (Exterior Elevations): Revised opening size for the 'Knockout Panel' for the Large Autoclave.
  • DWG A-401 & A-403 (Enlarged Restroom Plans and Details/Elevations): Clarifications on shower and chase wall type.
  • DWG A-404 (Enlarged Restroom Elevations and Shower Details): Detailing for revised shower wall.
  • DWG A-501 & A-502 (Wall Type Details): Revisions to Wall Types B, C, D, F, G, H, and J.
  • DWG A-503 (Wall Type Details): Revision to Wall Type L.
  • DWG I-601 & I-602 (Schedules & Legends): Revised Room Finish Schedule and Finish Legend.
  • DWG M-502 (Mechanical Details): Omission of Detail A1.

• Revised Specifications for P995: Several specification sections have been revised or replaced:

  • Section 07 61 14.00 20 (CP Steel Standing Seam Roofing): Warranty revised to include a 5-year general contractor bonded weathertightness warranty for damages caused by winds up to 139 mph.
  • Section 12 24 13 (Roller Window Shades): Entire section replaced; changes made to paragraph 2.1.2.1 and 2.1.3.2.
  • Section 22 00 00 (Plumbing, General Purpose): Addition regarding high and low pressure vacuum piping systems (304 stainless steel).
  • Section 23 64 26 (Chilled-Hot Water Piping Systems): Addition regarding above ground piping (4 inch and smaller must be Type L copper).
  • Section 25 05 11.01 (Cybersecurity for FA/MNS Facility-Related Control System): New section added.
  • Section 41 22 23.19 (Monorail Hoists): Nominal length revised to 419 feet.
  • Section 45 52 00 (Aerospace X-Ray Testing Equipment): Entire section replaced; revisions made to paragraph 3.4.

• Pre-Proposal Inquiry (PPI) Responses: Additional PPI responses have been provided (attached separately).

• Section 00 00 00 - Procurement and Contracting Requirements

• Section 00 30 00 - Available Information

• Various sections of the P995 specifications and drawings.

• Section 00 73 00 - Supplementary Conditions

• The proposal due date has been extended to May 20, 2026.

• Bidders must review all revised drawings, specifications, and PPI responses to ensure their proposals are compliant.

Amendment / Modification

This document is Amendment 0004 to Section 45 52 00, "Aerospace X-Ray Testing Equipment." It revises the document dated 24 December 2025, with the amendment effective 17 APR 2026.

• The document title indicates it is Amendment 0004, revising Section 45 52 00.
• The footer of each page consistently states "REVISED Amendment 003 - 17 APR 2026", suggesting this is a consolidated revision or that Amendment 0004 is part of a series of revisions.

This amendment likely impacts the technical specifications and requirements for the Aerospace X-Ray Testing Equipment. Bidders should review the full document to understand all changes to scope, deliverables, or submission requirements.

Amendment / Modification

This document is Amendment 0004 to the P995 opportunity. It includes revisions to the drawings and specifications. Specifically, it references changes to the floor plan (Area C), exterior elevations, restroom plans, wall type details, and room finish schedules.

• Sheet A-104 (Floor Plan - Area C): Contains revisions.
• Sheet A-201 (Exterior Elevations): Contains revisions.
• Sheet A-401 (Enlarged Men's Room Plan): Contains revisions.
• Sheet A-402 (Enlarged Women's Room Plan): Contains revisions.
• Sheet A-403 (Enlarged Restroom Elevations): Contains revisions.
• Sheet A-404 (Enlarged Restroom Details): Contains revisions.
• Sheet A-501 (Wall Type Details): Contains revisions.
• Sheet A-502 (Wall Type Details): Contains revisions.
• Sheet A-503 (Wall Type Details): Contains revisions.
• Sheet I-601 (Room Finish Schedule): Contains revisions.
• Sheet I-602 (Finish Legend): Contains revisions.

This amendment introduces changes to the project's design and specifications. Bidders should review all updated sheets to ensure their proposals accurately reflect the latest requirements. No specific impact on proposal deadlines or evaluation factors is mentioned in this amendment, but bidders must ensure their bids are based on the most current documentation.

Amendment / Modification

This document is Amendment 003, dated 17 APR 2026, to Section 25 10 10, "UTILITY MONITORING AND CONTROL SYSTEM (UMCS) FRONT END AND INTEGRATION". The amendment revises various sections of the original specification.

• The amendment revises content throughout Section 25 10 10, including but not limited to:
  • Section 1.1 SUMMARY and System Requirements
  • Section 1.1.1.2 BACnet Requirements
  • Section 1.1.1.3 OPC Requirements
  • Section 1.1.2 Symbols, Definition and Abbreviations
  • Section 1.1.3 System Units and Accuracy
  • Section 1.1.4 Data Packages/Submittals Requirements
  • Section 1.2 RELATED SECTIONS
  • Section 1.3 REFERENCES
  • Section 1.4 DEFINITIONS
  • Section 1.5 SUBMITTALS
  • Section 1.6 PROJECT SEQUENCING
  • Section 1.7 QUALITY CONTROL (QC) CHECKLISTS
  • Section 1.8 OPERATION AND MAINTENANCE (O&M) INSTRUCTIONS
  • Part 2 PRODUCTS (Section 2.1 EQUIPMENT REQUIREMENTS, Section 2.2 CONTROL HARDWARE, Section 2.3 COMPUTER HARDWARE)
  • Part 3 EXECUTION (Section 3.1 DRAWINGS AND CALCULATIONS, Section 3.2 INSTALLATION REQUIREMENTS, Section 3.3 INSTALLATION OF EQUIPMENT, Section 3.4 INTEGRATION OF FIELD CONTROL SYSTEMS, Section 3.5 START-UP AND START-UP TESTING, Section 3.6 PERFORMANCE VERIFICATION TEST (PVT), Section 3.7 MAINTENANCE AND SERVICE, Section 3.8 TRAINING)
• Appendix A QC CHECKLIST is also affected.

This amendment does not appear to directly alter submission deadlines or evaluation factors, but it modifies the technical requirements and procedures that bidders must adhere to. Bidders should review all revised sections to ensure their proposals and subsequent execution align with the updated specifications.

Amendment / Modification

This document is Amendment 003, revising Section 12 24 13, Roller Window Shades. The revision date is April 17, 2026.

• Section 12 24 13 (Roller Window Shades) is affected.

This amendment does not appear to alter submission deadlines or evaluation criteria, but bidders should review the revised specification for any changes to product requirements.

Questions & Answers / Clarifications

This document contains responses to pre-proposal inquiries (PPI) related to the solicitation, providing clarifications on various technical and contractual aspects of the opportunity.

• Settlement Monitoring (Q115): Confirms no additional surcharge is required for fill placement and a 90-day settlement monitoring period.
• CMMC Level 2 Requirements (Q151, Q156, Q193, Q194, Q196): Multiple questions address the burden of CMMC Level 2 certification on small businesses, potential impacts on schedule and pricing, and requests for clarification on which specific documents or scopes require this certification. The government confirms CMMC Level 2 applies to P993 which contains CUI.
• Composite Curing Ovens (Q152, Q153, Q154): Clarifications are sought and provided regarding door configurations (vertical lift vs. swinging), operating temperatures, dimensions, and the number of required ports.
• Testing and Material Specifications (Q158, Q172, Q173, Q174, Q177, Q179, Q183): Questions arise about the removal of RCP testing requirements, the use of specific pipe materials (Type L copper, 304 SS), and the application of exterior coating specifications.
• Delegated Design Scope (Q185, Q186, Q187, Q188, Q189, Q190, Q191, Q192): Several inquiries focus on the scope of delegated design, particularly concerning crane systems, foundation requirements, and the extent of the contractor's responsibility for system development and potential infrastructure upgrades.
• Small Business Participation (Q151, Q155): Questions are raised about the feasibility of meeting the 40% small business participation target and a request is made to revise it to 10% due to the burden of CMMC Level 2 certification.
• Drawing and Specification Discrepancies (Various): Numerous questions highlight discrepancies between drawings and specifications regarding bypass connections, pipe schedules, utility line sizes, and the location/installation of components like oil water separators.

These clarifications address potential ambiguities and provide necessary details for bidders to accurately prepare proposals. Some questions indicate potential impacts on pricing, schedule, and the ability of small businesses to participate. Several responses are marked as "PENDING RESPONSE," indicating that further clarification is forthcoming.

Amendment / Modification

This document is a Class Justification and Approval (CJ&A) for the use of other than full and open competition for Facilities Related Controls Systems (FRCS) at MCAS Cherry Point, NC. It authorizes the use of brand name Johnson Controls International (JCI) Metasys product line for Facility Related Control Systems (FRCS) building heating, ventilating, and air conditioning (HVAC) system Direct Digital Controllers (DDC).

• Authority: The CJ&A is authorized from 15 May 2025 to 14 May 2030.
• Supplies/Services: Requires JCI Metasys DDC for projects needing connection to the Cherry Point Facility Related Control Systems (CPFRCS). This includes specific JCI Metasys software and various controller types.
• Estimated Value: The total estimated value for JCI brand name Metasys product line equipment through 29 April 2030 is not specified but is noted as a small percentage of total construction cost.
• Statutory Authority: Justification is based on Title 10, U.S.C. 3204(a)(1) and FAR 6.302-1, citing "Only one responsible source and no other supplies or services will satisfy agency requirements."
• Rationale: Standardization and interoperability with the existing CPFRCS are critical for cost reduction, cybersecurity, and operational efficiency. A business case analysis supports the need for JCI Metasys to minimize costs and avoid duplication of effort.
• Cybersecurity: JCI Metasys controllers and software are required to maintain a defensible cybersecurity posture and obtain/maintain Authority to Operate (ATO).
• Competition Efforts: A Sources Sought announcement was issued, receiving three responses from contractors, not manufacturers. One proposed alternative system was deemed not to meet essential requirements or provide anticipated benefits.
• Future Competition: MCAS Cherry Point will monitor the controls industry for universal controller configurations to assess future competition feasibility.

This document does not directly impact proposal submission deadlines for a specific solicitation but rather justifies the procurement strategy for future contracts related to FRCS at MCAS Cherry Point.

Amendment / Modification

This document is Amendment 0003 to Section 08 33 23, "Steel Overhead Coiling Doors," dated 24 December 2025. It revises the specification for steel overhead coiling doors.

• The entire specification document (Section 08 33 23) has been revised.
• Specific references to standards and publications have been updated.
• Details regarding submittals, quality control, system description, components, hardware, and installation have been modified.

Bidders should review the entirety of the revised specification to understand any changes to requirements, materials, installation, or testing procedures. The revision date of the document is 9 APR 2026.

Amendment / Modification

This document is Amendment 0003 to the solicitation, specifically revising sheet A-116, which details the Roof Plan.

• Sheet A-116 (Roof Plan) has been revised.

This amendment revises architectural drawings related to the roof plan. Bidders should ensure they are using the most current version of sheet A-116 for their proposals.

Amendment / Modification

This document is Amendment 0003 to the "A-407 REV1" drawing set. It was posted on April 15, 2026.

This amendment revises the drawing set titled "P-995 COMPOSITE REPAIR FACILITY ENLARGED PLAN & SECTIONS - WALK-IN FREEZER".

No specific impact on proposal deadlines or submission requirements is detailed in this amendment notice. Bidders should refer to the full amendment document for specific changes to the drawings.

Amendment / Modification

This document is Amendment 0003 to Section 45 52 00, "Aerospace X-Ray Testing Equipment." It revises the document dated 24 December 2025. The amendment number and date are updated throughout the document. Specifically, "REVISED Amendment 002 - 9 APR 2026" is now present at the bottom of each page, replacing previous amendment information.

All pages of Section 45 52 00 have been affected by this amendment, primarily to update the amendment number and date references.

This amendment does not appear to alter proposal deadlines, requirements, or evaluation factors. Its primary purpose is to update the document's revision history.

Amendment / Modification

This document is Amendment 0003 to Section 08 71 00, "Door Hardware," dated 02/16, CHG 4: 02/22. The revision date for this amendment is April 9, 2026.

This amendment revises the "SECTION 08 71 00" document.

No specific impact on proposal deadlines or submission requirements is detailed within this amendment document itself, as it pertains to the technical specifications of door hardware.

Amendment / Modification

This document is Amendment 002 to Section 08 11 16, "Aluminum Doors and Frames," dated 9 APR 2026. It revises the original specification, which was dated 24 December 2025.

• The entire specification Section 08 11 16 has been revised.
• Specific dates mentioned in the document have been updated to reflect the amendment.

This amendment updates the specification for aluminum doors and frames. Bidders should review the revised document to ensure their proposals and product selections align with the most current requirements, including performance standards, materials, fabrication, installation, and hardware schedules.

Questions & Answers / Clarifications

This document provides responses to pre-proposal inquiries regarding the P-993 F-35 Sustainment Center project, clarifying various technical and contractual aspects.

• Crane Type: The project requires an under-running bridge crane, and associated structural components (columns, framing, hangers) are designed for this. Runway beams are furnished by the Contractor. (Ref: Detail A1/S-504, Spec Para 1.3.1.3 corrected/revised)
• Warranty Duration: The 5-year warranty duration has been revised. Specifics are detailed in the revised 45 52 00 Specification provided with Amendment 0003.
• Regulatory Compliance: The specification for cabinet x-ray systems has been corrected to reference 21 CFR § 1020.40.
• Training: The specification for onsite training has been revised. Details are in the revised 45 52 00 Specification provided with Amendment 0003.
• Door Size: The door size for blade loading has been modified. See revised 45 52 00 Specification provided with Amendment 0003.
• Inspection Performance Criteria: The specification further defines performance criteria for acceptance, including target defect types, minimum defect size/sensitivity, and image quality standards. See revised 45 52 00 Specification provided with Amendment 0003.
• Inspection Throughput: The specification further defines inspection throughput/cycle time per blade. See revised 45 52 00 Specification provided with Amendment 0003.
• Blade Manipulator Degrees of Freedom: The specification further defines the information regarding the blade manipulator and scan system. See revised 45 52 00 Specification provided with Amendment 0003. A floor-mounted gantry is preferred.
• Door Type Conflict: A conflict between vertical lift doors and swing doors has been resolved; vertical lift doors are intended and paragraph 2.1.2 has been modified.
• RF Doors: Amendment 0003 provides a revision for the secure area vestibule/door.
• Pile Lengths: Estimated pile tip elevations are provided on sheet SS102 as part of Amendment 0003.
• X-Ray Testing Equipment: The revised 45 52 00 Specification provided with Amendment 0003 clarifies the required range of motion for the X-ray testing equipment.
• X-Ray Vault: The revised 45 52 00 Specification provided with Amendment 0003 provides complete specifications for the modular vault system.

Several sections of the 45 52 00 Specification have been revised and provided via Amendment 0003, impacting technical requirements, component specifications, and potentially pricing and scheduling. Bidders must review these amendments carefully. A question regarding the reduction of the small-business participation target from 40% to 20% due to CMMC Level 2 certification challenges is noted as PENDING RESPONSE.

Amendment / Modification

This amendment (0003) to solicitation N4008526R0002 incorporates several changes and additions to the original solicitation and related documents for the "DESIGN-BID-BUILD, P993/995 F35 SUSTAINMENT CENTER & COMPOSITE REPAIR FACILITY, MARINE CORPS AIR STATION, CHERRY POINT, NORTH CAROLINA" opportunity. The proposal due date of 28 April 2026 remains unchanged.

Key changes include:

• Revised Drawings for P993: Updates to General Notes, Historic Boring Site Locations, Historical Boring Logs, and Erosion and Sediment Control Plans across multiple phases. Specific changes include revised dates for tree clearing, added boring logs, and modifications to keynote descriptions for rip rap outlets. Several drawing sheets related to storm drain structure data tables, details, airfield typical sections, utility plans, and bridge foundation layouts have also been revised or updated.
• Revised Drawings for P995: Updates to Roof Plan, Enlarged Plan and Sections for Walk-in Freezer, Reflected Ceiling Plan, Framing Plan, Site Details, Partial Site Plan, and Partial Utility Plan. These include sheet replacements, corrected references, revised callouts, and updated keynote descriptions.
• Revised Specifications for P993: Removal of specifications for Electronic Security System Acceptance Testing and Electronic Security Systems. Revisions to Precast Prestressed Concrete Piles specification to require signed and sealed pile design calculations.
• Revised Specifications for P995: Updates to Aluminum Doors and Frames, Steel Overhead Coiling Doors, and Door Hardware specifications to clarify Electronic Safety and Security requirements. Revisions to Bridge Cranes, Overhead Electric, Under Running Trolley specifications regarding crane type and conformance. Modifications to Industrial Ovens specifications regarding operating temperatures, pressure, heating/cooling rates, and controls. Removal of the Risk Management Framework specification and submittal requirements. Deletions to Spare Parts and Precast Terrazzo Shower Floors specifications.
• Additional Pre-Proposal Inquiry (PPI) Responses: A new attachment titled "Amendment 0003 Pre-Proposal Inquiries" has been added under Section 00 73 00 - Supplementary Conditions.

Numerous drawing sheets (P993 and P995) and specification sections (P993 and P995) are affected. Refer to the amendment document for a comprehensive list of affected drawings and specification sections.

The proposal due date of 28 April 2026 remains unchanged. Bidders should review all updated drawings and specifications to ensure their proposals reflect the latest requirements.

Amendment / Modification

This document contains responses to pre-proposal inquiries (PPIs) and addresses several clarifications and potential changes to the solicitation. Key points include:

• Proposal Due Date Extension: The proposal due date has been extended to April 28, 2026, via Amendment 0002.

• Small Business Subcontracting Plan (SBSP): Guidance is provided on submitting the SBSP, allowing contractors to either base it on preliminary assumptions or submit an accurate SBSP by 5:00 PM EDT on bid day once selections are finalized.

• CLINs 0007 and 0014 (ESS): These CLINs have been removed from the Price Proposal Form. Further specification changes will be included in an upcoming amendment.

• Attachment F Price Proposal Form: A revised Attachment F Price Proposal Form has been provided with Amendment 0002.

• Crane System Clarification: Clarification is requested regarding whether an "Under Running" or "Top Running" bridge crane is required, and confirmation of whether the supporting structure is designed for the intended crane type.

• NAVSEA Manual S0420-AA-RAD-010: This document is not available for public release. The Government will release appropriate sections once the vendor for the X-ray equipment is selected.

• FRCE Quality Standards: Detailed requirements for FRCE quality standards, including testing procedures, acceptance criteria, and calibration, will be added by amendment.

• 1515DX Detector: The 1515DX detector is intended as a basis of design only; equivalent or superior detectors meeting performance requirements will be accepted.

• 5-Year Warranty: Clarification is sought regarding the 5-year warranty requirement for system components, particularly for critical components like the X-ray source and detector, which typically do not have such long manufacturer warranties.

• Vault and Manipulator Equipment: The use of a step-down transformer (480V to 240V) is confirmed as acceptable for meeting power requirements.

• X-ray Vault Construction: Confirmation is requested regarding the acceptability of self-shielded modular vault systems and cast-in-place concrete-shielded vault construction as an equivalent alternative.

• 21 CFR 1020.40: Confirmation is requested whether the intended regulation is 21 CFR § 1020.40.

• Onsite Training: Clarification is requested on whether the "two hours of onsite training" is the full requirement or if separate operator and maintenance training sessions are needed.

• Motorized Slider: Confirmation is requested on the 6'-0" height for the biparting motorized slider and whether it is a strict requirement or adjustable.

• Mark X System: The Mark X system is confirmed to be a feature that marks the blade for damage identification.

• Inspection Performance Criteria: Definition of required inspection performance criteria for acceptance is requested.

• Blade Manipulator Degrees of Freedom: Clarification is requested on the required degrees of freedom for the blade manipulator and scan system.

• Computer Hardware: Clarification is requested on the computer hardware requirements, specifically regarding the basis of design (tower workstation, laptop, or either) and whether it's a strict owner requirement or IT/cybersecurity standard.

• Paint Booth Hazard Evaluation: Clarification is requested regarding the Basis of Design for Hazard Evaluation and Dust Hazard Analysis, including identification of processes, materials, and expected concentrations. The Government will not pre-determine this; the contractor is responsible for analysis.

• Fire Alarm Devices: Fire alarm devices in locker rooms are confirmed to be weatherproof only, not explosive proof.

• Pile Caps: Pile caps are confirmed to be included in CLIN0001A.

• EP Panel Schedules: Electrical drawings are for circuiting only; mechanical and controls sheets provide location and connection information.

• Network Architecture: The network architecture shown is for general intent; the Controls Contractor must create the final DDC network architecture according to design guidelines and with Government approvals.

• Autoclave Airflow: The design intent is to maintain temperature uniformity regardless of airflow distribution configuration.

• Operating Pressures and Temperatures: Maximum operating pressure is confirmed at 150 psi and maximum operating temperature at 450 degrees F.

• Vacuum Sources and Thermocouples: Requirements for vacuum sources and thermocouples are being reconciled and will be modified by amendment.

• CPC 2024 Software: The software is intended as a basis of design only; other software meeting performance characteristics will be accepted.

• Vent Silencer: Refer to paragraph 3.8, AC-1 Small Composite Curing Autoclave item 10 for schedule.

• Vacuum Source Lines: The intent is for vacuum source lines to be computer controlled.

• Heating Rate Requirements: Prioritize uniformity and heating rate requirements and size accordingly.

• Control System Capabilities: Government requires control system capabilities as specified in 1.4.1.

• Door Type: Vertical lift doors are intended; paragraph 2.1.2 will be modified to eliminate conflict.

• Make-up Air Blower: 100% make-up air is required.

• Composite Ovens: CLIN 0023 is the large Composite Oven; CLIN 0024 includes six smaller composite ovens.

• Construction Security Plan: The CSP has been provided to the two General Contractors proposing on the projects previously.

• 3D Model Files: 3D files will be released to the successful offeror.

• Elevated Storage Tank Foundation: Foundation design to be included by the delegated design professional.

• M-608 Notes: MI861/B3 does not show/request DDC controls; the electric heater has a thermostat. The BCS Contractor will mount and wire the thermostat.

• UFGS 09 97 13.27: Shop applied coatings with field touch-up are acceptable; paragraph 2.2 and 1.4.6.5 are to be deleted.

• Shielding Effectiveness: The Contractor is responsible for providing a facility that meets plans and specifications. If spaces do not meet independent third-party testing, it will be investigated, and the Contractor will be required to repair areas that do not conform due to workmanship.

• Architectural Drawing Sheet Notes: Partition schedule is on A-519.

• HEMP Shielded Enclosures: Section 1.6.3 is to remain, but references to "EM" shielding are to be deleted.

• EMI Filter: Keynote 6 and 2 provide one EMI filter to one AWG #1.0 ground cable. No CAT-5/6 runs outside the secure space are shown.

• RF Shielded / STC-50 Doors: Pending response.

• CLT Roof to Steel Connection: See response to PPI #5.

• Building Control System (BCS) Panel: The intent is to have the BCS for all units on the roof mounted on the wall on the 1st floor.

• Paint Booth Toxicity Hazard Monitoring Panel: An "Intrinsically Safe" panel is required, not an "explosion proof" panel.

• Elect Room Vent Pipe: The dashed line is a buried sanitary line.

• Natural Gas Meter: Pulse meter is acceptable; gas sub-meter must have AMI capability.

• MH141 Keynote: Keynote 4 is not applicable.

• MH142 Detail Location: Section is intended for below roof ductwork.

• MP125 Heat Pump Units: Tag is missing; refer to MH125 for labels and M-609 for schedules.

• MP129 Pipe: Pipes penetrate the roof and serve DOAS-06.

• MP131 HRS Units: Refrigerant piping for heat pumps serving the secure area will enter the building and turn up. Heat pumps serving the first floor will turn down and enter the building through the roof.

• MI871/M1872: Agreed; the intent is for the Controls Contractor to provide 24Vac power distribution to terminal units.

• Fume Exhaust Extraction Systems: Downdraft booth requires an 18" exhaust duct connection. Controls integration is required.

• Paint Booth Integration: Controls/BAS integration is required.

• P-993/P-995 Paint Booths: Other manufacturers that meet requirements will be accepted; disregard Sources Sought.

• Collateral Equipment (CLIN 16): CLIN 0016 includes equipment; CLIN 0005E is for Paint Booth.

• Aircraft Work Stands: Confirmed CLIN 0015 should read "Collateral Equipment (Sheet I-606 for aircraft work stands".

• Optional Paint Booths (CLIN 5E/CLIN 16): Paint booths 3 and 4 are to be included in CLIN 0005E; CLIN 16 is for other collateral equipment inside the booths only.

• Contaminated Soils: Confirmed.

• FF&E and Collateral Equipment: Interior Designer / Equipment designer is not required for specific CLINs.

• QC Specialist Duties: Confirmed specialists can be employed by specialized technical companies.

• P-112 Ball Valves: The booth manufacturer will provide eyewashes; the plumbing contractor is responsible for providing DCW & DHW to the booth.

• P-107 Contaminated Waste Pit: Information is shown on Detail A4 on sheet P-503.

• Paint Booth Ductwork: Ductwork size and routing shown on plans are for coordination purposes only; exact requirements must be coordinated with the equipment manufacturer.

• Nitrogen Tank: The nitrogen tank size is a suggestion; it is GFGI and will be supplied by a local gas supplier.

• P-119 Vacuum Systems: Vacuum piping will be required in the booths and provided by the booth manufacturer.

• Emergency Shower/Eye Wash Stations: Confirmed, provide as code required.

• Division 1 Specifications: Combined in the P993 Specification.

• 3D Model Files: 3D Model files will be provided to the successful proposer after award.

• P-601/P-404 Faucets: Confirmed use of hardwired fixtures; low voltage wiring shall be provided from the fixture to the junction box.

• M-001 Exposed Ductwork: Provide double wall insulated for all exposed ductwork.

• MH102 Sand Booth: Delegated design is per Paint Booth Contractor per 41 34 23; clarify CLIN/Option.

• MH104 Specialty Equipment Sheets: Note refers to sheets MH110-MH111.

• MH401 Air Compressor Intake: AC unit exhaust is tied to L-6 & L-7. Refer to sheet M-907 and M-601.

• Gas Pipe Routing: Final gas routing/sizing is dependent on requirements of delegated design.

• RMF Specification: Concur with removing RMF specification.

• 33 40 00 - 2.3.5: Flexible, watertight connectors conforming to ASTM C923 requirement remain in the specification.

• 33 40 00 - 2.4.1: RCP suppliers cannot test concrete pipe by hydrostatic testing; remove this testing requirement.

• M-314 Ductwork: Ductwork size and routing are for coordination purposes only.

• M-711 Gas Meter: Correct, additional gas meter is to be provided for communication/monitoring through the BAS.

• M-601 Motorized Dampers: Propose per plans and specs.

• 26 29 23 - 1.8.1 Spare Parts: Delete paragraph 1.8.1.

• Fire Protection System Inspections: Provided in Specification section 01 45 00.

• Cybersecurity: No cybersecurity specifications associated with Division 41 and 42 items.

• Nitrogen Piping Material: Listed on Detail B1 on Sheet P-505.

• A-111 RCP Note #2: Confirmed, #2 tags are intended to be #1 "OPEN TO STRUCTURE ABOVE". All exposed overhead structure is to be painted.

• A-111 RCP Note #2 (COMM 144): Patterning indicating gypsum board ceilings is in error; confirmed intention is "OPEN TO STRUCTURE ABOVE".

• Painting of Canopies/Steel: Confirmed. Bid per specification paint tables in 09 90 00.

• CLIN0022 Composite Oven: Dependent on equipment manufacturer and available control options. Awarded contractor must coordinate with manufacturer and Government.

• Vault Door Opening: Door size has been amended.

• Vault Penetrations: Penetration into the enclosure shall be manufacturer's standard through walls or ceiling in an inconspicuous location.

• KV Tube Rotation: The KV tube does not rotate; specification will be revised.

• Modular Vault Components: Specs cover requirements for modular components.

• A3/A-301 Exterior Side: Confirmed upper wall condition is the same as depicted in detail C3/A-302.

• A3/A-302 Exterior Side: Confirmed; note applies to same area.

• CT126 Aircraft Work: Confirmed sunshades to be included in CLIN 0018.

• P-993 ES503 Sunshades: Base bid includes power for everything in cells 1 through 7, 13 and 14. Rough-in only for cells 8 through 12.

• P-993 CS117 Laydown Site: Construction dates for P-1055 have not been determined. Scuff and Refresh contract awarded.

• ERCES (BDA) NOTE: Disregard ERCES (BDA) NOTE; ERCES system is NOT IN CONTRACT.

• P-995 T-114 Devices: Confirmed.

• P-993 Laydown Area: Yes, contractor laydown area can be outside of the area of disturbance.

• Bridge Pile Lengths: Pending response.

• Pile Splicing: Splicing of piles is permitted for pile lengths over 55 feet.

• CLIN0001G/CLIN0002D: Revised CLIN0002D to tons to match CLIN 0001G.

• Project Identification Job Board: Provide one sign for each project.

• Aerospace X-ray Testing Equipment: Document is not available for public release; appropriate sections will be released once vendor is selected.

• Radiation Shielding Analysis: Pending response.

• Vault Penetrations: Penetration into the enclosure shall be manufacturer's standard through the walls or ceiling in an inconspicuous location.

• Additional Power Requirements: No additional equipment, systems, or accessories have additional power requirements.

• X-ray Tube/Manipulator Motion: Pending response.

• Modular Vault System: Pending response.

• Paint Booth Component Ratings: Specification will be revised regarding onsite training by amendment.

• Proposal due date

• SBSP submission requirements

• CLINs 0007 and 0014

• Attachment F Price Proposal Form

• Crane system requirements

• NAVSEA Manual S0420-AA-RAD-010 availability

• FRCE Quality Standards

• 1515DX Detector basis of design

• 5-year warranty clarification

• Vault and Manipulator Equipment power requirements

• X-ray vault construction

• 21 CFR 1020.40 clarification

• Onsite training requirements

• Motorized slider dimensions

• Mark X system functionality

• Inspection performance criteria

• Blade manipulator degrees of freedom

• Computer hardware requirements

• Paint booth hazard evaluation

• Fire alarm device type

• Pile cap inclusion

• EP panel schedule information

• Network architecture design

• Autoclave airflow design intent

• Operating pressures and temperatures

• Vacuum sources and thermocouple requirements

• CPC 2024 software basis of design

• Vent silencer requirement

• Vacuum source line control

• Heating rate requirements

• Control system capabilities

• Door type

• Make-up air blower requirement

• Composite oven CLINs

• Construction Security Plan availability

• 3D Model files release

• Elevated storage tank foundation design

• M-608 thermostat and DDC controls

• UFGS 09 97 13.27 coating application

• Shielding effectiveness testing responsibility

• Architectural drawing sheet notes for partitions

• HEMP shielded enclosure section removal

• EMI filter clarification

• RF Shielded/STC-50 door availability

• CLT roof to steel connection nailer type

• Building Control System (BCS) panel mounting location

• Paint booth toxicity hazard monitoring panel type

• Vent pipe clarification

• Natural gas meter type

• MH141 keynote applicability

• MH142 detail location

• MP125 heat pump unit labeling

• MP129 pipe routing

• MP131 HRS unit labeling and pipe routing

• MI871/M1872 24VAC power distribution

• Fume exhaust extraction system duct connection and controls integration

• Paint booth controls/BAS integration

• Paint booth supplier qualifications

• Collateral equipment CLINs for paint booths

• Aircraft work stand inclusion

• Optional paint booth CLINs

• Contaminated soils management

• FF&E and Collateral Equipment specialist requirements

• QC Specialist employment

• P-112 ball valve and check valve details

• P-107 contaminated waste pit details

• Paint booth ductwork sizing and routing

• Nitrogen tank sizing and type

• P-119 vacuum system inclusion

• Emergency shower/eye wash station quantity

• Division 1 specifications location

• 3D Model files release

• P-601/P-404 faucet wiring

• M-001 exposed ductwork insulation

• MH102 sand booth delegated design scope

• MH104 specialty equipment sheets reference

• MH401 air compressor intake ductwork layout

• Gas pipe routing to MAUs

• RMF specification removal

• 33 40 00 - 2.3.5 connector requirement

• 33 40 00 - 2.4.1 hydrostatic test requirement

• M-314 ductwork type and insulation

• M-711 gas meter type

• M-601 motorized damper location

• Spare parts requirement for ASD/VFDs

• Fire protection system inspection schedule

• Cybersecurity specification applicability

• Nitrogen piping material location

• A-111 RCP ceiling type

• A-111 RCP gypsum ceiling clarification

• Painting of canopies and structural steel

• CLIN0022 composite oven details

• Vault door opening size

• Vault penetration routing

• KV tube rotation parameter

• Modular vault component specifications

• A3/A-301 exterior wall condition

• A3/A-302 exterior wall condition

• CT126 aircraft work sunshade inclusion

• P-993 ES503 sunshade electrical rough-ins

• P-993 CS117 laydown site and construction dates

• ERCES (BDA) note removal

• P-995 T-114 device installation

• P-993 laydown area location

• Bridge pile lengths

• Pile splicing specifications

• CLIN0001G/CLIN0002D unit revision

• Project identification job board requirement

• Aerospace X-ray testing equipment document availability

• Radiation shielding analysis report

• Vault penetration routing clarification

• Additional power requirements for vault/X-ray equipment

• X-ray tube/manipulator motion parameters

• Modular vault system specifications

• Paint booth component ratings

• Proposal due date extended to April 28, 2026.

• Clarifications provided on SBSP submission.

• Revised Attachment F Price Proposal Form issued.

• Several sections of the specification will be revised by amendment based on PPI responses.

Form / Attachment / Pricing Sheet

This document, "AMENDMENT 0002 Attachment F - Price Proposal Form Revised.docx," is a revised price proposal form associated with Amendment 0002. It requires bidders to provide line item pricing for various components of the P-993 F-35 Sustainment Center and P-995 Composite Repair Facility projects, including base prices and several option items.

• Base Prices: Detailed line items for P-993 (CLINs 0001-0001H) and P-995 (CLINs 0002-0002D), covering construction, sitework, specialized work like soil undercut and debris removal, foundation piling, and equipment.
• Option Items: Includes pricing for various options for P-993 (CLINs 0003-0008, 0015-0022) and P-995 (CLINs 0009-0014, 0023-0027). These options cover contaminant impacted soil disposal, dewatering effluent treatment, additional paint spray booths, solar arrays, bridge cranes, FF&E, A/V equipment, and design services.
• Government Estimated Prices: Provided for many option items (CLINs 0015-0027) to indicate the projected magnitude of effort for FF&E, A/V, and Collateral Equipment.
• Handling and Administration Rate (HAR): Bidders may propose a HAR not to exceed 5% for FF&E, A/V, and Collateral Equipment.
• Blank Fields: Bidders must provide unit prices and sub-totals where indicated by blank underlines.

This form is critical for bidders to accurately price the base requirements and all potential option items. It dictates the format for submitting pricing proposals. Bidders must pay close attention to the specific descriptions for each CLIN, including quantities and units of measure. The form also highlights the government's estimated costs for certain optional items, providing a benchmark for bidders. Bid notes specify that award will be made on the total sum of CLINs 0001-0002, and options (CLINs 0003-0014) may be exercised within 365 days. A firm fixed price is required for options. The form also details specific bid notes for FF&E, A/V, and Collateral Equipment, including HAR percentages and bonding requirements.

Amendment / Modification

This amendment (0002) to solicitation N4008526R0002 modifies the original solicitation for the DESIGN-BID-BUILD, P993/995 F35 SUSTAINMENT CENTER & COMPOSITE REPAIR FACILITY at MARINE CORPS AIR STATION, CHERRY POINT, NORTH CAROLINA.

Key changes include:

• Extension of the proposal due date to April 28, 2026, no later than 1400 EDT.

• Revision of the Price Proposal Form (attached separately).

• Inclusion of Pre-Proposal Inquiry (PPI) Responses (PPI #1-151) (attached separately).

• Section 00 00 00 - Procurement and Contracting Requirements: The Response Due Date has been changed from April 21, 2026, to April 28, 2026.

• Section 00 73 00 - Supplementary Conditions: The attachment "AMENDMENT 0002 Pre-Proposal Inquiries" has been added.

The proposal due date has been extended. Bidders should note the revised date and utilize the updated Price Proposal Form and PPI Responses.

Other / Unclassified

This document is a marketing flyer from Global Finishing Solutions (GFS) highlighting their "Paint Booths for Refinishing Military Aircraft." It details GFS's role as a leading provider of state-of-the-art paint booths and finishing systems for military aircraft, emphasizing their ability to meet specific environmental control requirements for high-performance aircraft coatings.

The flyer lists numerous U.S. Air Force, U.S. Army, U.S. Marine Corps, and U.S. Naval bases, as well as foreign military locations, where GFS has installed or is installing aircraft paint booths. This information could be relevant to bidders by indicating:

• The extensive experience and established presence of GFS in the military aviation sector.
• Potential past performance or familiarity with specific military installations.
• The types of aircraft and environments their systems are designed to accommodate.

The document also outlines GFS's full-service approach, including project management, installation, startup, and energy efficiency, which may be of interest to potential prime contractors or subcontractors involved in aircraft maintenance or facility upgrades.

Other / Unclassified

This document is a brochure from Global Finishing Solutions (GFS) detailing their "Paint Booths for Gen 4, 5, & 6 Aircraft." It highlights GFS's capabilities as a manufacturer of specialized finishing solutions for military aircraft, emphasizing their experience with U.S. military branches and foreign allies.

This document is relevant to bidders as it showcases the type of specialized equipment and services Global Finishing Solutions provides to defense organizations. It demonstrates their track record and technological capabilities in designing and installing aircraft paint booths, particularly for advanced aircraft generations. The document lists specific U.S. Air Force, Army, Coast Guard, and Navy bases, as well as foreign military entities, where GFS has installed equipment, and details the types of aircraft their equipment can accommodate. This information can help potential bidders understand GFS's expertise and capacity in this niche market.

Form / Attachment / Pricing Sheet

This document is a "Sources Sought – Contractor Information Form" intended to collect general information from potential contractors. Bidders are instructed to limit their response to one page.

• Contractor Information: Fields for UEI, CAGE Code, Firm Name, and Address.
• Point of Contact (POC): Name, Phone Number, and Email of the firm's POC.
• Type of Business: Checkboxes for various SBA certifications and small business designations (e.g., 8(a), HUBZone, SDVOSB, VOSB, WOSB, EDWOSB).
• Bonding Capacity: Information on Surety Name, Maximum bonding capacity per project, and Aggregate maximum bonding capacity.
• Additional Information: A space to clarify any requested items.

This form is used to gather essential details about a contractor's business, certifications, and bonding capabilities. Completing and submitting this form is likely a required step for vendors interested in participating in the opportunity, helping the government assess contractor suitability and potential set-aside options.

Amendment / Modification

This amendment modifies the solicitation N4008526R0002 with the following changes:

• The proposal due date has been extended to April 21, 2026, at 2:00 PM EDT.

• Liquidated Damages clause (52.211-12) has been modified to state liquidated damages will be $35,391.79 per calendar day of delay.

• A revised Price Proposal Form is attached.

• The "Contract Description" section has been updated to reflect a change in CMMC requirements for P993 from Level 1 to Level 2.

• Several CLINs/SLINs/ELINs have been modified, including Option Line Items 0022, 0023, 0024, and 0025, with specific changes detailed in the document.

• Section 00 70 00 - Conditions of the Contract, specifically clause 52.211-12 Liquidated Damages-Construction, has been updated.

• The proposal due date has been extended to April 21, 2026.

• Bidders should note the revised Price Proposal Form and the updated CMMC requirements for P993.

Form / Attachment / Pricing Sheet

This document, "Amendment 0001 Attachment F - Price Proposal Form Revised," is a revised pricing schedule required for bidders to submit their price proposals. It outlines the specific line items (CLINs) for which unit prices and sub-totals must be provided.

• Base Price Items: Includes detailed breakdowns for P-993 F-35 Sustainment Center (CLINs 0001-0001H) and P-995 Composite Repair Facility (CLINs 0002-0002D). These cover various aspects like total project price, work within the 5-foot line, sitework, undercut and replacement of unsuitable soils, foundation piling, paint spray booths, demolition of buried debris, and water towers.
• Option Items: Details pricing for various options for both P-993 (CLINs 0003-0008, 0015-0022) and P-995 (CLINs 0009-0014, 0023-0027). Options include contaminant impacted soil disposal, dewatering effluent treatment, additional paint spray booths, solar arrays, electronic security systems, bridge cranes, composite ovens, collateral equipment, audio-visual systems, and furniture, fixtures, and equipment (FF&E).
• Government Estimated Prices: Provided for many option items (CLINs 0015-0027) to indicate the projected magnitude of effort for FF&E, A/V, and Collateral Equipment.
• Handling and Administration Rate (HAR): Bidders may propose a HAR not to exceed 5% for FF&E, A/V, and Collateral Equipment.

Bidders must carefully complete this form with accurate unit prices and sub-totals for all base CLINs and any desired option CLINs. The government will evaluate offers based on the total price, including options. Specific instructions are provided regarding the handling of unit prices versus extended totals and the potential for option exercise within 365 days. Additional bonding requirements are noted if options are exercised. For FF&E, A/V, and Collateral Equipment, bidders must consider the government's estimated prices and the fixed HAR percentage.

Other / Unclassified

This document comprises detailed technical specifications for the P-995 Composite Repair Facility project located at Marine Corps Air Station Cherry Point, NC. It is organized into two volumes, covering Divisions 00-13 and Divisions 21-45, and outlines comprehensive requirements for construction and facility systems.

Key areas detailed include:

• General Requirements & Existing Conditions: Demolition and site preparation.
• Materials & Structures: Concrete, masonry, metals (structural steel, framing), wood, composites, thermal/moisture protection (roofing, insulation), openings (doors, windows), finishes (flooring, painting), and specialties.
• Special Construction: Cold-storage rooms.
• Mechanical Systems: Fire suppression, plumbing, HVAC (including testing, balancing, insulation, controls, piping, air systems, dehumidifiers), and integrated automation with a focus on cybersecurity for control systems.
• Electrical Systems: Power studies, transformers, generators, transfer switches, lightning protection, interior and exterior lighting.
• Communications: Telecommunications cabling and distributed antenna systems (DAS).
• Safety & Security: Interior fire alarm and mass notification systems.
• Site Work: Earthwork (including definitions for fill materials, soil types, and subsurface data), exterior improvements, and utilities.
• Industrial Equipment: Material processing/handling, process heating/cooling/drying, and manufacturing equipment.

This document is essential for potential bidders to fully understand the technical scope, requirements, and standards for the P-995 Composite Repair Facility. It specifies materials, installation methods, quality assurance, performance criteria, and numerous industry standards (e.g., ASTM, NFPA, ASHRAE, IEEE). Bidders must review these specifications to accurately estimate costs, plan project execution, and prepare required submittals such as shop drawings, product data, and test reports. Understanding the definitions and references, particularly for earthwork, is crucial for compliance and accurate bidding.

Form / Attachment / Pricing Sheet

This document contains the "P-995 Composite Repair Facility" drawings, Volume 4 of 4. It details the electrical site and electrical systems for the facility.

• Electrical site plans
• Electrical legends and symbols
• Electrical riser diagrams
• Panel schedules
• Equipment connection schedules
• Lighting schedules
• Details for various electrical components and installations (e.g., grounding, duct banks, security enclosures, lighting fixtures).

This document is crucial for bidders to understand the scope and requirements related to the electrical systems and infrastructure for the P-995 Composite Repair Facility. It provides detailed information on power distribution, lighting, grounding, and specialized electrical systems necessary for the project.

Drawings / Plans

This document contains a comprehensive set of architectural and engineering drawings for the P-995 Composite Repair Facility at Marine Corps Air Station Cherry Point, NC. The drawings are organized into multiple volumes covering:

• Volume 1 of 4: General Information and Life Safety
• Volume 2 of 4: General, Architectural, Interior Design, Fire Alarm, and Fire Protection
• Volume 3 of 4: General, Plumbing, and Mechanical
• Volume 4 of 4: General, Electrical Site, Electrical, and Telecommunications

The drawings include detailed floor plans for waste and vent systems, water systems, compressed air and vacuum systems, and mechanical HVAC across various areas (A through F). They also feature enlarged plans for specific areas like hygiene facilities, break rooms, mechanical rooms, and riser diagrams. Additionally, the document contains various details for plumbing, mechanical equipment, and ATFP (Anti-Terrorism/Force Protection) bracing.

• Project: P-995 Composite Repair Facility
• Location: Marine Corps Air Station Cherry Point, NC
• Issuing Agency: Naval Facilities Engineering Systems Command (NAVFAC) Mid-Atlantic, Design and Construction Facilities Engineering and Acquisition Division, Norfolk, Virginia.
• Drawing Organization: The drawings are divided into four volumes, with detailed plans for plumbing, mechanical (HVAC), compressed air/vacuum, water systems, and controls, as well as specific details and schedules for equipment and components.
• Governing Regulations: The project adheres to Unified Facilities Criteria (UFC), Uniform Accessibility Standards (UFAS), International Mechanical Code (IMC), National Electric Code (NEC), and International Plumbing Code (IPC).

These drawings are critical for potential bidders to understand the full scope of work, including the layout, systems, materials, and specific requirements for the construction of the Composite Repair Facility. They provide detailed information on plumbing, mechanical, electrical, telecommunications, and life safety systems, as well as specific construction details and schedules for equipment. Bidders should review these drawings thoroughly to accurately estimate costs, plan their approach, and ensure compliance with all specified standards and regulations.

Form / Attachment / Pricing Sheet

This document contains architectural drawings for the P-995 Composite Repair Facility at Marine Corps Air Station Cherry Point, NC. It includes title sheets, location maps, general project notes, governing regulations, symbol legends, abbreviations, index of drawings, floor plans for various areas (A through F), reflected ceiling plans, air and moisture barrier details, exterior elevations, building sections, wall sections, knockout wall details, hazardous waste sump/disposal details, restroom plans and elevations, entrance and office details, roof details, stair details, freezer details, tool cage and autoclave pit details, dumpster enclosure details, signage plans, and furniture and collateral equipment plans.

• Project Title: P-995 Composite Repair Facility
• Location: Marine Corps Air Station Cherry Point, NC
• Issuing Agency: Naval Facilities Engineering Systems Command (NAVFAC) Mid-Atlantic
• Architectural Firm: MBF Architects, P.A.
• Drawing Set: Includes architectural, structural, mechanical, electrical, plumbing, fire protection, and interior design information.
• Key Areas Covered: Floor plans, reflected ceiling plans, exterior elevations, building sections, wall sections, details for specific components (e.g., autoclaves, dumpster enclosures, signage, furniture, fire suppression systems), and finish schedules.

These drawings are critical for bidders to understand the full scope of the construction project, including the layout, design, materials, and specific details of the proposed facility. They provide the technical specifications and visual representations necessary for accurate bidding and construction planning.

Form / Attachment / Pricing Sheet

This document comprises Volume 1 of 4 of the "P-995 Composite Repair Facility" drawings, providing detailed architectural and engineering plans for a new facility at Marine Corps Air Station Cherry Point, NC. It includes essential information for understanding the project's scope, design, and site conditions.

• General Information: Title sheet, location maps, general project notes, and drawing index for all four volumes.
• Life Safety: Details on life safety requirements, codes, occupant loads, and egress information, including comprehensive floor plans.
• Geotechnical Data: General notes, exploration plans (soil borings, cone penetration tests), and subsurface soil profiles (Sections A-A').
• Site Conditions: Survey control points, existing conditions plans (overall and specific areas), demolition plans (overall and specific areas), and site plans (overall and specific areas).
• Pavement & Site Details: Specifications for pavement sections (asphalt and concrete), curb and gutter, bollards, sidewalks, drainage structures, and utility details.
• Erosion Control: Specifications for sediment control measures.
• Structural Details: Structural notes, foundation plans, framing plans, sections, truss elevations, and general construction details for slab-on-grade, CMU walls, foundations, crane supports, and equipment pads.

These drawings are critical for bidders to comprehend the full scope of the construction project. They provide detailed insights into the facility's design, layout, structural requirements, life safety systems, site considerations, geotechnical conditions, demolition scope, and proposed site improvements. This information is essential for accurate cost estimation, developing construction methodologies, planning for site challenges (like subsurface conditions and utilities), and ensuring compliance with all specified requirements.

Form / Attachment / Pricing Sheet

This document is a template for an Individual Small Business Subcontracting Plan (SBSP), designed for use by large businesses (other than small businesses) responding to solicitations that require such a plan per FAR 19.704 and FAR clause 52.219-9. It outlines the requirements for establishing subcontracting goals and reporting on their achievement.

• Contract Information: Fields for Solicitation/Contract Number, Project Title/Location, and Date Prepared.
• Subcontracting Goals: Requires detailed goals for subcontracting to Large Businesses (LB) and various categories of Small Businesses (SB), including HUBZone SB, WOSB, SDB, VOSB, SDVOSB, AbilityOne, and Alaskan Native Corporations & Indian Tribes. It specifies that these goals are percentages of the total subcontracted value (Line 1.b).
• Products/Services: Sections to list principal products and services planned for subcontracting to both LB and SB categories, including firm subcontract commitments.
• Methodology: Requires explanation of how subcontracting goals were developed and how potential sources were identified, including reliance on SAM.gov.
• Program Administration: Details the responsibilities of the individual administering the subcontracting program.
• Reporting: Outlines requirements for submitting Individual Subcontract Reports (ISR) and Summary Subcontract Reports (SSR) via the Electronic Subcontracting Reporting System (eSRS).
• Record Keeping: Specifies the types of records to be maintained to document compliance.

Bidders (specifically large businesses) must complete and submit this plan as part of their proposal if required by the solicitation. It demonstrates their commitment to small business participation. Potential subcontractors can use this document to understand the types of services and products the prime contractor intends to subcontract and to identify potential opportunities within specific small business categories.

Form / Attachment / Pricing Sheet

This document, Attachment C, is a mandatory form for all offerors (both large and small businesses) to provide historical small business utilization and achievements. It serves as supporting information for the evaluation of Factor 6, Small Business Utilization and Participation.

• Project Details: Offerors must complete this section for three chosen projects, including contract number, project title, offeror's business size, performance role (prime, subcontractor, JV), and whether a subcontracting plan was required.
• Actual vs. Goal Columns: For each project, offerors must provide both the 'Actual' subcontracted dollar values and percentages, and the 'Goal' percentages if applicable. The 'Actual' column is required for all projects, regardless of whether goals were established.
• Subcontracting Breakdown: This section requires detailed reporting of subcontracted values and percentages for various categories, including overall Small Business Concerns, Large Business Concerns, Small Disadvantaged Business (SDB), Women-Owned Small Business (WOSB), HUBZone Small Business, Veteran-Owned Small Business (VOSB), and Service-Disabled Veteran-Owned Small Business (SDVOSB).
• Unmet Goals/No Achievement: Specific sections are provided for detailed explanations if goals were unmet or if there was no small business subcontracting achievement.
• Definitions: Key terms such as Total Project Dollar Value, Total Self-Performed Value, and Total Subcontract Value are defined.

Accurate and complete submission of this form is crucial for the evaluation of Factor 6. Bidders must carefully document their historical small business utilization, ensuring all percentages are rounded to the nearest tenth. Failure to use the provided format or to complete the form as instructed may result in non-evaluation. Offerors are permitted to expand portions of the form to provide sufficient detail.

Form / Attachment / Pricing Sheet

This document, Attachment D - Small Business Participation Commitment Document (SBPCD), is a mandatory form for all offerors (both large and small businesses) responding to RFP N40085-26-R-0002. It is used to provide supporting information for the evaluation of Factor 6, Small Business Utilization and Participation. This is the sole form that will be evaluated for determining the offeror's small business participation commitment; alternative formats will not be considered.

• Offeror Information: Requires identification of the prime contractor's business size (Large Business or Small Business) based on the solicitation's NAICS code. If a Small Business, applicable socioeconomic categories (SDB, WOSB, EDWOSB, HUBZone SB, VOSB, SDVOSB) must be indicated.
• Subcontracting Breakdown: Requires the Total Contract Value (TCV), the value of work to be self-performed by the prime, and the total value of work to be subcontracted.
• Small Business Participation Table: Offerors must detail the dollar value and percentage of the TCV to be subcontracted to various small business categories, including Total Small Business (SB), Small Disadvantaged Business (SDB), Woman-Owned Small Business (WOSB), HUBZone SB, Veteran-Owned Small Business (VOSB), and Service-Disabled Veteran-Owned Small Business (SDVOSB). The minimum total small business subcontracting requirement is 20% of the TCV.
• Firm Commitments Table: If subcontracting firm commitments are in place, offerors should list the Company Name, Small Business Category(ies), Products/Services, and Nature of Commitment (e.g., written teaming agreement). Commitments must be in writing.
• Explanations: Sections are provided for detailed explanations if the minimum 20% small business participation is not met, if no subcontractors with firm commitments are identified, or if a large business offeror does not intend to subcontract.

This form is critical for proposal preparation and evaluation. Offerors must accurately complete all sections to demonstrate their commitment to small business utilization, which is a specific evaluation factor. Failure to meet the minimum 20% small business participation or provide required explanations may impact the evaluation of the proposal.

Solicitation / RFP / RFQ

This solicitation is for the construction of the F-35 Sustainment Center and Composite Repair Facility at Marine Corps Air Station (MCAS) Cherry Point, North Carolina. The F-35 Sustainment Center will be a 255,461 SF depot-level hangar to support 20 F-35 aircraft, including maintenance bays, paint booths, administrative space, and modification shops. The Composite Repair Facility will be a 105,755 SF consolidated depot-level facility for advanced composites and rotor blade repair, including specialized shops and laboratory space. The project is being procured under an Early Contractor Involvement (ECI) framework, with two offerors pre-qualified for Segment II (construction services).

• Construction of a 255,461 SF F-35 Sustainment Center hangar and associated facilities.

• Construction of a 105,755 SF Composite Repair Facility.

• Site development including utility improvements, taxiway, and aircraft parking apron.

• Includes requirements for CMMC Level 1 (P995) and CMMC Level 2 (P993).

• Contract Type: Firm Fixed Price (FFP).

• Period of Performance: 15 calendar days for commencement after notice to proceed, and 1,461 calendar days for completion.

• Magnitude of construction is over $500,000,000.

• Proposals are due by 02:00 PM local time on 06 Apr 2026.

• Evaluation will be based on a tradeoff process, with technical factors (Management Approach & Schedule, and Small Business Utilization) being of equal importance to each other and approximately equal to price.

• Proposals must be submitted electronically via PIEE in PDF format, with price and non-price proposals in separate files.

• Key submission requirements include executed SF1442, completed Price Proposal Form, Bid Bond (SF-24), SAM registration, FAPIIS information, and VETS-4212 registration.

• This acquisition is for Segment II and two offerors have been pre-qualified.

• Small business subcontracting targets are: SB 40%, SDB 5%, HUBZone SB 3%, WOSB 9%, SDVOSB 5%.

• This solicitation includes DFARS 252.204-7025 and 252.204-7021 regarding Cybersecurity Maturity Model Certification (CMMC) Level Requirements.

• Drawings and specifications contain CUI and will not be posted to PIEE/Sam.gov; they will be provided separately upon completion of a DOD-CUI Non-Disclosure Agreement.

Form / Attachment / Pricing Sheet

This document is a Non-Disclosure Agreement (NDA) required for individuals or entities granted access to Controlled Unclassified Information (CUI) related to a government contract or opportunity. It outlines the terms and conditions under which CUI will be accessed, handled, and protected.

• Agreement to Protect CUI: Signers agree not to disclose CUI to unauthorized individuals or entities.
• Scope of CUI: Defines CUI as information requiring safeguarding or dissemination controls by law, regulation, or policy, excluding classified information.
• Training Acknowledgment: Signers attest to having undergone training on CUI protection.
• Reporting Breaches: Obligation to report any unauthorized disclosures of CUI.
• Consequences of Breach: Violation may result in cancellation of access, civil/criminal sanctions, and denial of future access.
• Acknowledgement: Requires the signer to confirm they have read the agreement, had questions answered, and understand the terms.

Bidders who will be handling CUI as part of this opportunity must understand and agree to the terms of this NDA. This document is critical for ensuring compliance with government regulations regarding sensitive information and may impact proposal preparation if specific CUI handling procedures are detailed or implied.

Form / Attachment / Pricing Sheet

This document, "Attachment F - Price Proposal Form," is a pricing schedule that bidders must complete to provide line item prices for various components of the P-993 and P-995 projects. It outlines the structure for submitting costs associated with base prices and various options.

• Line Items: Detailed breakdown of costs for specific work items, including base prices for P-993 (F-35 Sustainment Center) and P-995 (Composite Repair Facility), as well as numerous options for both projects.
• Cost Categories: Includes pricing for base work, subtotals for specific project areas (e.g., outside the 5-foot line, sitework), specialized tasks like unsuitable soil replacement, foundation piling, demolition of buried debris, paint spray booths, solar arrays, security systems, bridge cranes, and contaminant impacted soil disposal.
• Options: Clearly delineates optional work for P-993 and P-995, covering items such as additional paint spray booths, solar arrays, security systems, bridge cranes, contaminant handling, dewatering effluent treatment, and various FF&E, A/V, and Collateral Equipment.
• Units: Specifies units for pricing, such as Each (EA), Cubic Yards (CY), Linear Feet (LF), Tons, and Gallons (GAL).
• Pricing Fields: Requires bidders to provide Unit Price and Sub-Total for each line item, culminating in a Total Price.

This form is critical for bidders to accurately price their proposals for the P-993 and P-995 projects. It dictates the format for cost submission, including base requirements and all potential option items. Bidders must carefully review each line item, understand the scope of work associated with it (as detailed in other contract documents), and provide firm fixed prices for all CLINs, especially the options, as they will be evaluated for award purposes. The document also references specific bid notes regarding the award of CLINs and the handling of FF&E, A/V, and Collateral Equipment, which bidders must consider when preparing their pricing strategy.

Form / Attachment / Pricing Sheet

This document is a vendor registration guide for the Procurement Integrated Enterprise Environment (PIEE) platform, specifically for the PIEE Solicitation Module. It provides step-by-step instructions for new and existing users to register for a PIEE account and obtain the necessary roles to submit offers or view solicitations.

• New User Registration: Covers self-registration for a PIEE user account, including selecting the 'Vendor' user type, creating a User ID and password, setting up security questions, completing user profile and supervisor/company information, selecting roles (Proposal Manager or Proposal View Only), entering a CAGE code, providing justification, and verifying registration details.
• Existing User Role Addition: Details how existing users can log in, navigate to 'My Account,' select 'Add Additional Roles,' verify profile information, and follow steps similar to new user registration to add roles.
• Roles and Functions: Explains the two primary vendor roles: 'Proposal Manager' (required to submit offers) and 'Proposal View Only' (for viewing solicitations). It also outlines specific actions and menu items available to each role.
• Support Information: Provides links and contact details for getting started, account support, and technical support.

This guide is crucial for any vendor intending to respond to solicitations posted on the PIEE platform. It outlines the mandatory registration process, the roles required to participate in the solicitation process (especially submitting an offer), and how to obtain those roles. Bidders must complete this registration and obtain the appropriate role before they can submit proposals or quotes through PIEE.

Form / Attachment / Pricing Sheet

This document is a Pre-Proposal Inquiry (PPI) Form associated with Solicitation N4008526R0002 for P993 F-35 Aircraft Sustainment Center & P995 Composite Repair Facility at MCAS Cherry Point, NC. It is intended for potential bidders to submit questions or seek clarifications regarding the solicitation.

• The form includes fields for the submitter's information (Name, Company, Contact Information).
• It provides space to reference specific sections, paragraphs, or pages of the solicitation to which the question pertains.
• A dedicated section is available for bidders to clearly state their questions.

This form is crucial for bidders who have questions or require clarification on any aspect of the solicitation. Submitting inquiries through this form ensures that questions are formally recorded and can be addressed by the government, potentially leading to official answers that may be shared with all interested parties. This helps ensure a level playing field and allows bidders to submit more accurate and compliant proposals.

Form / Attachment / Pricing Sheet

This document is a "Reference Sheet" (I-603 & I-604 Dated 12/2025) detailing interior finishes for the FY25 MCON Project P-993, F-35 Sustainment Center at MCAS Cherry Point, Havelock, NC. It specifies materials, manufacturers, colors, sizes, and quantities for various interior finishing elements.

• Concrete Floor Sealer and Hardener: Specified for 24,690 SF.
• Architectural Cabinets: Includes plastic laminate clad cabinets from Wilsonart in various finishes (Skyline Walnut, Manitoba Maple, Graphite) for casework, accent walls, and custom millwork.
• Solid Surfacing: Wilsonart and Avonite solid surfaces specified for horizontal surfaces, transaction tops, wall panels, and shower pans.
• Decorative Window Film: 3M Fasara film for reception areas.
• Tiling: Crossville tile specified for walls, floors, and mosaic accents, with Schluter profiles for edges and transitions.
• Acoustical Ceilings: Includes Turf beams and Armstrong ceiling tiles (Ultima, Lyra Plant Based) in various configurations and locations.
• Static Control Flooring: Nora Envirecare static dissipative flooring.
• Resilient Tile Flooring: Patcraft LVT, Johnsonite rubber base, and Nora resilient flooring for treads and risers.
• Precast Terrazzo: David Allen Company precast terrazzo for staircases and base.
• Resinous Matrix Terrazzo Flooring: David Allen Company terrazzo flooring in custom colors and chip sizes for lobby and accent areas.
• Standard Resinous Flooring: Sherwin Williams Resuflor products for various applications including seamless epoxy flooring, corridors, and safety striping.
• Fuel Resistive Resinous Flooring: Sherwin Williams Resuflor system for hangar bays.
• Tile Carpeting: Shaw Contract Group carpet tiles in various colors and patterns.
• Rigid Grid Access Flooring: Specified for the Telecom Node Building.
• Vinyl Wall Covering: Koroseal digital lab custom vinyl wall covering for break rooms.
• Acoustical Wall Panels: Turf Monolith panels specified for interior elevations.
• Interior Painting: Sherwin Williams latex and epoxy paints for walls, ceilings, accents, and metal components.
• High Performance Coating for Steel Structures: Sherwin Williams coatings for exposed metal structures and crane rails.
• Toilet Compartments: Scranton Hiny Hiders toilet partitions.
• Wall Protection: Inpro and Marlite wall protection systems.
• Roller Window Shades: Mechoshade roller shades in various configurations (electroshade, manual double shades).
• Upholstery: Knoll Textiles specified for seating.

This document is critical for bidders to understand the specific materials, finishes, and quantities required for the interior construction of the F-35 Sustainment Center. It directly impacts material selection, procurement, and installation planning for any contractor bidding on this project. Bidders must ensure their proposals accurately reflect these specified finishes and their associated costs.

Form / Attachment / Pricing Sheet

This document is a "P995 Interior Finishes J&A Form" (Job Action Form) dated December 2025, for the P-995 Composite Repair Facility. It details the specific products, manufacturers, models, colors, sizes, and quantities of various interior finishes required for the facility. This form serves as a reference for materials to be used in the project.

• Acoustical Ceilings: Armstrong products in various models and sizes.
• Corner Guards: Inpro products.
• Carpet Tile: Patcraft product.
• Fiberglass Reinforced Plastic: Marlite products.
• Toilet Partitions: HDP/Scranton Products.
• Luxury Vinyl Tile: Patcraft product.
• Cabinets: Formica and Hafele products.
• Epoxy Resinous Flooring: Sherwin-Williams products.
• Paint: Sherwin-Williams paint colors.
• Wall Base: Roppe and Marlite products.
• Signage: 290 Signs and 292 Signs products.
• Countertops: Meganite product.
• Shower Compartments: Corian product.
• Sealed Concrete: Quantity specified.
• Floor Tile: Mosaic Tile products.
• Wall Tile: Architessa products.
• Transitions: Schluter Systems and Marlite products.
• Wood Doors: Masonite Architectural product.

This form is crucial for bidders to understand the specific materials and finishes that are to be incorporated into the P-995 Composite Repair Facility project. It provides detailed specifications for items such as flooring, wall coverings, ceilings, doors, and other interior components, which will be essential for accurate bidding, material procurement, and project execution.